Abstract:1671-7694/2014/S12302(5) S12302-1 © 2014 Chinese Optics Letters Vibration monitoring is one of the most effective methods in mechanical equipment monitoring and fault diagnosis field. The vibration monitoring mainly uses the electromagnetic vibration sensors, such as piezoelectric sensor. Although the technology is well-developed with excellent performance, its disadvantages are poor ability to resist electromagnetic interference, signal not transmitted over long distance, difficult to achieve large-scale network. So, it is difficult to realize real-time and largescale monitoring for the vibration state of mechanical equipment in the flammable, explosive and electromagnetic interference situation[1,2]. Owing to many advantages of fiber Bragg grating (FBG) technology, since the emergence in late 70’s, though it has aroused a great concern, it has been developing very rapidly. After 2000, research and application of the technology have started in the vibration monitoring of mechanical equipment, and resulted in a few achievements[3,4]. But the existing FBG accelerometers are largely one-way, unable to meet the needs of three-dimensional vibration measurement. Then if one-way accelerometer is used, it requires at least three accelerometers for better functionality, which increases the cost of testing. Often, because of the installation space constraint, multiple sensors cannot be installed in the same monitoring point; eventually, testing data cannot reflect the real acceleration value in different directions of the monitoring point. However, so far, reports of 3D FBG accelerometer are rare; there is no report especially on 3D FBG accelerometer used in vibration monitoring of mechanical equipment. Hence, the research on the sensor is the focus of the paper[5–7]. In addition, in order to solve the problem of vibration signal demodulation speed, a light intensity demodulation method is adopted based on matched filter. But the method has one obvious disadvantage, namely, low measurement accuracy, which is caused by attenuation of light source and line loss. Solving of this problem is also considered in this paper. Figure 1 shows the 3D FBG accelerometer studied in this paper, which is composed of three unidirectional sensing units that are mutually vertical. Each sensing unit is composed of a base, an elastomer, a mass block and two FBGs, and its structure and principle are shown in Fig. 2. Two FBGs written in the same optical fiber are formed into precise matching by accurate fabrication process, and they are symmetrically fixed between the base and the mass block. In order to avoid dead zone, they are pre-stretched about 1 nm. When the sensor receives the vibration signal from the outside world, the mass supported by the elastic membrane vibrates up and down in order to drive the FBGs axial expansion, envelope area of reflection peaks of FBG1; and FBG2 Research on 3D FBG accelerometer and demodulation method

Design, Simulation and Optimisation of a Fibre-optic 3D Accelerometer

Optical Design and Analysis of a High Resolution MOEMS Accelerometer Based on Diffraction Grating

A MOEMS Accelerometer Based on Diffraction Grating with Improved Mechanical Structure.

Design and Modification of a High-Resolution Optical Interferometer Accelerometer

Three-Dimensional Vector Accelerometer Using a Multicore Fiber Inscribed With Three FBGs

A Novel Differential Optical Fiber Accelerometer

New Fiber Bragg Grating Three-Dimensional Accelerometer Based on Composite Flexure Hinges

Design of a practical intensity modulated dynamic optical fiber accelerometer

Design Of A Novel Optical Acceleration Sensor

Research and Design of A Large Phase Shift Fringe Count Interferometric Fiber-Optic Accelerometer

Fiber Optic Accelerometer Based on Fiber-Mirror Interference Cavity

Medium-High Frequency and High Sensitivity Fiber Optic Acceleration Sensor Based on F-P Interference

Research on an optimized optical fiber accelerometer for well logging

Miniature Tri-Axis Accelerometer Based on Fiber Optic Fabry-Pérot Interferometer.

A High-precision 3D Vibration Acceleration Sensor Based on FBGs

Research on 3 D FBG accelerometer and demodulation method

A Novel Optical Accelerometer Based on Slant-Ended Fiber

An Isogeometric Analysis Based Design of Highly Sensitive and Precise Omnidirectional Piezoelectric-Fiber Accelerometer

High Sensitivity Fiber Optic Acceleration Sensor Based on Fabry -Perot Interferometer

Design and Experiment of All Polarization-maintaining Fiber-optic Vector Accelerometer

Design and Experimental Research on Cantilever Accelerometer Based on Fiber Bragg Grating