Abstract:Micro-electro-mechanical system (MEMS) is a newly rising interdisciplinary, technology. The mechanical design of MEMS is one of the frontiers of mechanical engineering. The increasing use of small micro-electro-mechanical system (MEMS) and advanced sensors has lead to concern about the failure modes and reliability of these structures. This depends on the solution of materials issues associated with the design and fabrication of complex MEMS devices. The reliable mechanical properties of these thin films are critical to the safety and functioning of these microdevices and should be accurately determined. This paper takes up the key point among the existing problems in the development of MEMS, the mechanical behavior of MEMS materials, for investigating experimentally in detail. To investigate the specimen size influence on fracture strength of microstructures, the validity of a novel, direct and convenient method for bending strength measurements by beam bending using a nanoindenter has been demonstrated. The tensile strength of polysilicon thin films was measured with a microtensile test device with a magnet solenoid actuator and a fibre optical displacement sensor. The bending strength of microfabricated polysilicon beams with dimensions of 16 ∼ 34 μm long, 10 ∼ 50 μm wide, and 2.4 μm thick was evaluated. The tensile mechanical properties of microfabricated polysilicon thin films with dimensions of 100 ∼ 660 μm long, 20 ∼ 200 μm wide, and 2.4 μm thick were also evaluated. The result shows that bending strength and tensile strength of polysilicon microstructures show size effect on the size of the specimens. Statistical analysis of bending strength and tensile strength for various specimen sizes shows that the average bending strength of polysilicon microcantilever beams is (2.885 ± 0.408) GPa, and the average tensile strength of polysilicon thin films is (1.36 ± 0.14) GPa. Statistical analysis of the specimen size effects on the tensile strength predicated the size effects on the length, the surface area and the volume of the specimens due to microstructural and dimensional constrains. The fracture strength increases with the increase of the ratio of surface area to volume. In such cases the size effect can be traced back to the ratio of surface area to volume as the governing parameter. The test data accounts for the uncertainties in mechanical properties and may be used in the future reliability design of polysilicon MEMS structures.

System-Level Simulation and Fabrication of On-Chip Fatigue Bending Test Structure for Micro-Scale Polysilicon Films

A Novel Approach to Study Patterned Thin Film Local Stress for Microelectronics Application

An Out-Chip Method for Measuring Fatigue Property of Polysilicon Thin Film

Evaluation of Mechanical Properties and Strain Criterion for Realibility Design of Micromachined Polysilicon Thin Films

Monotonic and fatigue testing of spring-bridged freestanding microbeams application for MEMS

Design of a Micro-scale Silicon Film Bending Fatigue Testing Device Based on the Resonance Principle

Micromechanical Characterization of Polysilicon Films through On-Chip Tests

Experimental investigation and multiscale simulation on the bending fatigue of 2D SiCf/SiC composites

FATIGUE PROPERTY OF POLYSILICON THIN FILMS IN AMBIENT ENVIRONMENT

An integrated push-to-pull micromechanical device: Design, fabrication, and in-situ experiment

Microcracking in On-Chip Interconnect Stacks: FEM Simulation and Concept for Fatigue Test

Fatigue behaviour analysis of thermal cyclic loading for through-silicon via structures based on backstress stored energy density

Experimental and computational analysis of bending fatigue failure in chopped carbon fiber chip reinforced composites

Micro 3D Measurement Applied to Interfacial Deformation of Bilayer Thin Film/substrate Structure under Thermal Cycling Loads

MEASUREMENT OF THE FRACTURE PROPERTY OF POLYSILICON MICRO STRUCTURE

RESEARCH OF THE SIZE EFFECT ON STRENGTH OF POLYSILICON MICRO-ELECTRO-MECHANICAL DEVICES

A Dual-Parameter On-Chip Test Platform Based on Thermal Actuator for Testing Fracture Strength of Microstructure

Structural Design and Optimization of the Milling Force Measurement Tool System Embedded with Thin-Film Strain Sensors

STUDY ON A MEMS FATIGUE TESTING DEVICE BASED ON THE RESONANCE PRINCIPLE

Experimental investigation and multiscale simulation on the bending fatigue of SiCf/SiC composite vanes

A Universal Structure for Self-Aligned in Situ On-Chip Micro Tensile Fracture Strength Test