Abstract:SiC ceramics were successfully soldered with the assistance of ultrasound. Two kinds of filler metals, namely non -eutectic Zn-5Al-3Cu and eutectic Zn-5Al alloys, were used. The effects of ultrasonic action on the microstructure and mechanical properties of the soldered joints were investigated. The results showed that ultrasound could promote the wetting and bonding between the SiC ceramic and filler metals within tens of seconds. For the Zn-5Al-3Cu solder, a fully grain-refined structure in the bond layer was obtained as the ultrasonic action time increased. This may lead to a substantial enhancement in the strength of the soldered joints. For the Zn-5Al solder, the shear strength of the soldered joints was only -102 MPa when the ultrasonic action time was shorter, and fractures occurred in the brittle lamellar eutectic phases in the center of the bond layer. With increasing ultrasonic action time, the lamellar eutectic phase in the bond layer of SiC joints could be completely transformed to a fine non-lamellar eutectic structure. Meanwhile, the grains in the bond layer were obviously refined. Those results led to the remarkable enhancement of the shear strength of the joints (similar to 138 MPa) using the Zn-5Al solder, which had approached that enhancement using the Zn-5Al-3Cu solder. The enhanced mechanical properties of the joints were attributed to the significant refinement of the grains and the change in the eutectic structure in the bond layer. Prolonged enhanced heterogeneous nucleation triggered by ultrasonic cavitation is the predominant refinement mechanism of the bond metals of the SiC joints.

Microstructure and Strength of Si3N4 Joints Bonded with Sialon-Oxynitride Glass

Microstructure and Properties of Porous Si3N4/Dense Si3N4 Joints Bonded Using RE–Si–Al–O–N (RE = Y or Yb) Glasses

Microstructure and Properties of Porous Si3N4/Dense Si3N4 Joints Bonded Using RE-Si-Al-O-N (RE = Y or Yb) Glasses

Joining of Si3N4 Ceramics with In-situ Formed Oxynitride Glass Interlayer

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Microstructure Evolution and Mechanical Properties of Porous Si3N4 and Dense Si3N4 Joints Bonded Using CaO–Li2O-Al2O3–SiO2 Glass-Ceramic

Joining of Cf/SiC composites and Si<sub>3</sub>N<sub>4</sub> ceramic with Y<sub>2</sub>O<sub>3</sub>-Al<sub>2</sub>O<sub>3</sub>-SiO<sub>2</sub> glass filler for high-temperature applications

The Wettability of Y–Al–Si–O–N Oxynitride Glasses and Its Application in Silicon Nitride Joining

Microstructure, Mechanical Property and Bonding Mechanism of SiC Ceramic Joint Using a Novel Y2Si2O7/Mullite Glass-Ceramic Interlayer

Joining Dense Si3N4 to Porous Si3N4 Using a Novel Glass-Ceramic Interlayer with Precipitated Β-Lialsi2o6/mg2sio4

Microstructure and Enhanced Joint Performance of Porous Si3N4 Ceramics in Ultrasonic Soldering

Microstructure Evolution and Mechanical Properties of SiO2f/SiO2 Composites Joints Brazed by Bismuth Glass

Study on the mechanism of glass-SiC-glass anodic bonding process

Joining Pre-Oxidized Dense Si3N4 to Porous Si3N4 with Β-Spodumene Based Glass-Ceramic Interlayer

Microstructure and Strength of Ultrasonic-Assisted Brazed Joints of Si3N4/6061Al Composites

Process and Properties of Brazing High Volume SiCp/6063Al Composites with Glass

Microstructure evolution and interfacial bonding mechanisms of ultrasonically soldered sapphire/Al dissimilar joints using Sn-based solders

Bonding and Strengthening Mechanism on Ultrasonic-Assisted Soldering of Sapphire Using Sn-3.5Ag-4Al Solder

Microstructural Evolution of SiC Joints Soldered Using Zn-Al Filler Metals with the Assistance of Ultrasound.

Effects of Glass Composition and Joining Parameters on Microstructural Evolution and Mechanical Properties of Al2O3/Cu Joints Brazed with Bi2O3-B2O3-ZnO Glass