Abstract:Direct electrodeposition (ECD) process of copper film on ultra-thin molybdenum film is investigated in both copper sulfate - sulfuric acid (CuSO4 - H2SO4) acidic bath and copper sulfate - ethylenediamine (CuSO4 - En) neutral bath (pH=7.5). The neutral electrolyte containing 0.03M CuSO4 and 0.06M En was chosen to avoid excessive corrosion of Mo and introduction of other ions. The complexing effect of En affects the electrodeposition process of Cu on Mo. Potentiodynamic polarization curves and scanning electron microscopic characterization show that Cu can be electroplated in CuSO4 - En bath with lower corrosion rate, greater nucleation density and shorter fully-covering time than that in CuSO4 - H2SO4 bath. The fitting results of current-time transients using Scharifker and Hill's model support the instantaneous nucleation and growth of Cu on Mo in both CuSO4 - H2SO4 bath and CuSO4 - En bath (with background electrolyte) at the initial stage of electrodeposition. By using an optimized two-step plating process (at the current density of 8mA/cm2 in the first step for a short time and 4mA/cm2 in the second step), the resistivity of direct ECD Cu on Mo was almost the same to that of ECD Cu on Cu/Mo in the same plating bath. Display Omitted The direct electrodeposition of Cu on Mo in neutral bath was reported originally.Corrosion rate of Mo is much lower in neutral bath than that in acidic bath.Hemispherical Cu nuclei are achieved in neutral bath rather than dendritic ones.The density Cu nuclei on Mo in neutral bath is much higher than that in acid bath.A two-step plating process was applied to lower the resistivity of direct ECD Cu.

Direct copper plating on ultra-thin sputtered cobalt film in an alkaline bath

Direct copper electrodeposition onto cobalt adhesion layer in alkaline bath

Electrodeposition of Cu on CoTa Barrier in the Alkaline CuSO4-Ethylenediamine Solution

Direct copper electrodeposition on novel CoMo diffusion barrier

Superconformal Copper Electroplating on an Ultrathin Cobalt Seed in an Acidic Copper Sulfate Electrolyte

Electroless Plating of Copper via a Sn-Free Process on Dielectric SiLK Surface Modified by UV-Induced Graft Copolymerization with 4-Vinylpyridine and 1-Vinylimidazole

Study of Direct Cu Electrodeposition on Ultra-Thin Mo for Copper Interconnect

Structure and Properties of Electrocodeposited Cu-Al2o3 Nanocomposite Thin Films

Effect of Electroplating Bath Composition on Corrosion Resistance of Deposited Cobalt Films

Plasma-Enhanced Atomic Layer Deposition of Cobalt Films Using Co(EtCp)2 As a Metal Precursor.

COPPER PLATING FROM NON-CYANIDE ALKALINE BATHS

Electroless Deposition of Pure Co on TaN Substrate for Interconnect Metallization

Low-temperature copper-copper quasi-direct bonding with cobalt passivation layer

Study of A Single Layer Ultrathin Como Film As A Direct Plateable Adhesion/Barrier Layer for Next Generation Interconnect

Electrodeposition of Nanostructured Co–Cu Thin Alloy Films on to Steel Substrate from an Environmentally Friendly Novel Lactate Bath under Different Operating Conditions

Electrochemical processes for the production of copper interconnects on non-metallic barrier layers

Influences of Co and process parameters on structure and corrosion properties of nanocrystalline Ni-W-Co ternary alloy film fabricated by electrodeposition at low current density

Effect of Coxmoy As Single Barrier Layer on Properties of Directly Electroplated Copper Films

Electrodeposition of Ni–Co alloys from a deep eutectic solvent

Electroless Copper Deposition for Ultralarge-Scale Integration

Super-flat and uni-oriented cobalt film electrodeposited by modulating the crystal nucleation and growth behavior