Abstract:Thermoelectric energy conversion is an all solid-state technique offering high reliability and power density, desirable properties in mobile waste heat recovery applications. It is generally less efficient than vapor-based thermodynamic cycles. The efficiency of thermoelectric (TE) power generators and heat pumps is characterized by the thermoelectric figure of merit zT = S2σT/κ; here S is the thermopower or Seebeck coefficient of the TE material, κ and σ = 1/ρ are its thermal and electrical conductivities (ρ is the resitivity). Recent research led to a doubling of zT over the last decade. Featuring lattice thermal conductivities intrinsically limited by very strong phonon-phonon interactions to the amorphous limit,[1] small band gaps[2–4] and interesting transport properties,[2,5] some ternary I–V–VI2 intermetallic compounds like AgSbTe2 can reach a thermoelectric figure of merit zT ∼ 1.3 at 400 K[6] when doped p-type. Its alloys with GeTe, called “TAGS”,[7–9] and with PbTe, called “LAST”,[10] are the materials that have some of the highest known zT near 500–800 K, the temperature of automotive exhaust where heat recovery applications are being envisioned. Here we complement the work on AgSbTe2-PbTe and AgSbTe2-GeTe and report the first systematic study of the thermoelectric properties of AgSbTe2SnTe alloys covering the entire alloy range. This goes beyond early work[7,11] concentrated on the SnTe-rich side, and mixed alloys of SnTe, PbTe and AgSbTe2, “LASTT”.[12,13] In large-scale energy recovery applications, SnTe-based alloys would avoid lead-abatement legislation, the technological problems associated with a crystallographic phase transition in GeTe-based alloys, and the very high cost of Ge. The high zT of p-type AgSbTe2 stems from the large density of states (DOS) of the valence band[2] and the intrinsically ultralow thermal conductivity,[1] but it is difficult to dope AgSbTe2 sufficiently to get a good zT. Binary SnTe is plagued by the existence of an irreducible concentration of Sn vacancies which makes it impossible to reach a low hole concentration. Here we

Thermoelectric Properties of Non-Stoichiometric Agsbte2 Based Alloys with A Small Amount of Gete Addition

Thermoelectric properties of (GeTe)1-x[(Ag2Te)0.4(Sb2Te3)0.6]x alloys

Effect of Ag/Sb Ratio on the Thermoelectric Properties of (gete) 85 (Agysb2-Yte3-y)15 TAGS Alloys

Optimized Carrier Concentration and Enhanced Thermoelectric Properties in GeSb4-xBixTe7 Materials

Mid-temperature Thermoelectric Performance of Zone-Melted Sb2(Te,Se)3 Alloys Near Phase Transition Boundary

Thermoelectric Properties of Quaternary Ag-Bi-Sb-Te Alloys

Thermoelectric Properties of Ag Doped Pseudo-binary Alloys (PbTe)1-x(SnTe)x

Phase compositions, nanoscale microstructures and thermoelectric properties in Ag2-ySbyTe1+y alloys with precipitated Sb2Te3 plates

Enhanced Thermoelectric Performance of Ag0.8Pb18SbTe20 Alloyed with Se

Influence of Ag2te Doping on the Thermoelectric Properties of P-Type Bi0.5sb1.5te3 Bulk Alloys

Co-alloying of Sn and Te enables high thermoelectric performance in Ag9GaSe6

Structural transformation and thermoelectric performance in Ag2Te1−Se solid solution

Doping Effect on Thermoelectric Properties of Nonstoichiometric AgSbTe 2 Compounds

Band convergence and nanostructure modulations lead to high thermoelectric performance in SnPb0.04Te-y% AgSbTe2

Enhancing the Thermoelectric Performance of GeSb4Te7 Compounds via Alloying Se

The role of Ge vacancies and Sb doping in GeTe: A Comparative Study of Thermoelectric Transport Properties in Sb<sub>x</sub>Ge<sub>1-1.5x</sub>Te and Sb<sub>x</sub>Ge<sub>1-x</sub>Te Compounds

Influence of Ag_2Te Doping on the Thermoelectric Properties of p-type Bi_(0.5)Sb_(1.5)Te_3 Bulk Alloys

Thermoelectric Properties of Ag-doped N-Type (bi2te3)0.9–(bi2−xagxse3)0.1 (x=0–0.4) Alloys Prepared by Spark Plasma Sintering

Thermoelectric performance of (AgBiTe2)1-x(SnTe)x with stable cubic enabled by enhanced configurational entropy

SnTe–AgSbTe2 Thermoelectric Alloys

Improved Thermoelectric Properties of AgSbTe2 Based Compounds with Nanoscale Ag2Te in Situ Precipitates