Abstract:Cold-rolled AZ31 Mg alloy strips, with a reduction of 33 pct, were subjected to electropulse treatment (EPT) and conventional heat treatment (HT) to evaluate the respective influences of electropulses and temperature on the recrystallization behavior of AZ31. The highest measured temperature during the EPT (543 K) was used in HT. The electron backscattered diffraction results demonstrated that the EPT-stimulated recrystallization was completed within 8 seconds, whereas for HT, recrystallization was still far from completion even after 240 seconds. It was found that both the nucleation and grain growth of these two processes were totally different. In the EPT samples, nucleation tended to occur preferentially near extension twin boundaries and grain boundaries by continuous recrystallization, whereas in the HT samples, nucleation occurred mainly by grain boundaries bulging via discontinuous recrystallization. As grain growth proceeded, the texture intensities of the EPT samples decreased gradually and finally evolved into an obvious transverse-direction-split texture. This is likely attributable to the impact of electropulses on the boundary energy and the contribution of nonbasal dislocations; however, the basal-type textures of the HT samples were notably strengthened, which is associated with a 30 deg〈0001〉 orientation with respect to the deformed texture.

Static Electropulsing-Induced Microstructural Changes and Their Effect on the Ultra-Precision Machining of Cold-Rolled AZ91 Alloy

Electropulsing-induced Phase Transformations and Their Effects on the Single Point Diamond Turning of a Tempered Alloy AZ91

Mechanism of Electropulsing Induced Recrystallization in a Cold-Rolled Mg–9Al–1Zn Alloy

Microstructure and texture evolution of the cold-rolled AZ91 magnesium alloy strip under electropulsing treatment

Microstructure and Mechanical Properties of Cold-Rolled Mg-6Al-1Zn Alloy Strip Treated by Electropulsing Treatment

Influence of Electropulsing Treatment on Microstructure and Mechanical Properties of Cold-Rolled Mg–9Al–1Zn Alloy Strip

Electropulsing-induced Phase Transformations in a Zn-Al-based Alloy

Microstructure and texture evolution of cold-rolled Mg-3Al-1Zn alloy by electropulse treatment stimulating recrystallization

Accumulation and Annihilation Effects of Electropulsing on Dynamic Recrystallization in Magnesium Alloy

Improved Plasticity of Mg–Al–Zn Alloy by Electropulsing Tension

Thermal and Electromigration Effects of Electropulsing on Dynamic Recrystallization in Mg–3Al–1Zn Alloy

Microstructure and Texture Evolution of Magnesium Alloys During Electropulse Treatment

Dynamic Electropulsing Induced Evolution of Basal Texture and Its Effect on Properties of Magnesium Alloy Az61

Texture Evolution in Cold-Rolled AZ31 Magnesium Alloy During Electropulsing Treatment

Effect of Electroplastic Treatment on Microstructure and Texture Changes of a Cold Rolling AZ31 Strip

A Comparative Study on the Static Recrystallization Behavior of Cold-Rolled Mg-3Al-1Zn Alloy Stimulated by Electropulse Treatment and Conventional Heat Treatment

Microstructural Modification and Mechanical Improvement of Ultrafine-Grained Ti Alloy Through Electron Wind Force: an Innovative Approach

Effect of Electropulsing on Recrystallization and Mechanical Properties of Silicon Steel Strips

Effects of Electropulsing on the Machinability and Microstructure of GH4169 Superalloy During Turning Process

Microstructure control of ultra-high-strength AlZnMgCu alloys fabricated by wire arc directed energy deposition: the role of variable polarity electric pulse

Enhancement of Ductility in Mg-3Al-1Zn Alloy with Tilted Basal Texture by Electropulsing