Abstract:In this paper, the electron backscatter diffraction (EBSD) technique was used to analyze the dynamic recrystallization (DRX), twinning, slip behavior, and texture evolution during forging and subsequent extruding deformation. The results show that, as the degree of strain increased (forging to extruding), the degree of DRX increased, and the DRX mechanism changed from discontinuous DRX (DDRX) during forging to DDRX and continuous DRX (CDRX) during extruding. Particle stimulation nucleation (PSN) promoting DRX occurred during deformation. The deformation process mainly produced {10–12} twins (TTW) and played a role in coordinating the deformation. The slip behavior also changed according to an analysis of in-grain misorientation axes (IGMA) results, changing from slip-dominated with a basal slip to co-dominated with multiple slip modes, with the activation of mainly prismatic and pyramidal slip. Meanwhile, the strong basal texture at the beginning of the deformation also changed, and the texture strength decreased from 24.81 to 15.56. The weakening of the texture was mainly due to the formation of DRX grains and twins, as the newly formed DRX and twins reoriented. In the later stages of deformation, the activation of prismatic slip and pyramidal slip changed the basal texture component. Based on microstructural analysis, the improvement in mechanical properties was due to fine-grain strengthening and load-transfer strengthening. The ultimate tensile strength (UTS) was 370.5 MPa, the yield strength (YS) was 340.1 MPa, and the elongation (EL) was 15.6%.

Dynamic Electropulsing Induced Evolution of Basal Texture and Its Effect on Properties of Magnesium Alloy Az61

Enhancement of Ductility in Mg-3Al-1Zn Alloy with Tilted Basal Texture by Electropulsing

Texture Evolution in Cold-Rolled AZ31 Magnesium Alloy During Electropulsing Treatment

Microstructure and Texture Evolution of Magnesium Alloys During Electropulse Treatment

Static Electropulsing-Induced Microstructural Changes and Their Effect on the Ultra-Precision Machining of Cold-Rolled AZ91 Alloy

Microstructure and texture evolution of the cold-rolled AZ91 magnesium alloy strip under electropulsing treatment

Accumulation and Annihilation Effects of Electropulsing on Dynamic Recrystallization in Magnesium Alloy

Enhanced Electroplasticity through Room-Temperature Dynamic Recrystallization in a Mg-3Al-1Sn-1Zn Alloy

Effect of electropulsing treatment on the recovery of AZ31B magnesium alloy

Improved Plasticity of Mg–Al–Zn Alloy by Electropulsing Tension

Abnormal Texture Development in Magnesium Alloy Mg–3Al–1Zn During Large Strain Electroplastic Rolling: Effect of Pulsed Electric Current

Plastic deformation of AZ31B magnesium alloy in the preform and electropulsing treatment process

Effect of Current Frequency on the Mechanical Properties, Microstructure and Texture Evolution in AZ31 Magnesium Alloy Strips During Electroplastic Rolling

Microstructure and texture evolution of cold-rolled Mg-3Al-1Zn alloy by electropulse treatment stimulating recrystallization

Thermal and Electromigration Effects of Electropulsing on Dynamic Recrystallization in Mg–3Al–1Zn Alloy

Electroplastic Effect in AZ31B Magnesium Alloy Sheet Through Uniaxial Tensile Tests

Microstructure and Texture Evolution of Mg-3Zn-1Al Magnesium Alloy During Large-Strain Electroplastic Rolling

Enhanced Rollability of Mg-3al-1zn Alloy by Pulsed Electric Current: A Comparative Study

Dynamic Recrystallization, Texture Evolution, and Improved Mechanical Properties of Mg-Y-Zn-V Alloy during Forging and Subsequent Extruding Deformation

Texture Modification of Magnesium Alloys During Electropulse Treatment

The Recovery Behavior of AZ31B Magnesium Alloy Stimulated by Electropulsing Treatment and Heat Treatment