Abstract:Tungsten alloy has a wide range of applications in aerospace and defense industry because of its high hardness, high strength and other excellent properties. Tungsten alloys are typical hard-to-machine materials, and the electroplastic effect can improve the machining surface quality of hard-to-machine metal materials. However, the complex thermal–mechanical-electrical coupling generated by the relative motional squeezing of the tool and the workpiece under the electric pulse. It will cause a large difference between the physical and mechanical properties of the surface layer and the substrate material. The size and distribution of the characteristic parameters of the physical and mechanical properties of the machined surface, such as work hardening, residual stress and metamorphic layer, are not clear. Therefore, characterization of the physical and mechanical properties of the surface of W93NiFe alloy for electroplasticity-assisted dry turning machining was carried out in this paper. The results showed that the electrically plastic assisted dry turning process effectively alleviated the degree of work hardening on the machined surface of W93NiFe alloy. but the oxidation of the surface layer of the workpiece was exacerbated by excessive pulse voltage, which resulted in the increase of the surface microhardness again; Compared with conventional dry turning, the application of appropriate pulse voltage can effectively reduce the residual stress on the machined surface of W93NiFe alloy. and in this experiment, the variation of pulse frequency had less effect on the residual stress on the machined surface of W93NiFe alloy; After passing the pulse current, the thickness of the surface metamorphic layer increased significantly with the increase of electrical parameters such as pulse voltage and pulse frequency. but there was no significant effect of the two processing methods on the internal organization of W93NiFe alloy.

Effects of Electropulsing on the Machinability and Microstructure of GH4169 Superalloy During Turning Process

Effect of Electropulsing-Assisted Turning Process on AISI 5120 Cementation Steel

Effect of Electropulsing on Surface Mechanical Behavior and Microstructural Evolution of Inconel 718 During Ultrasonic Surface Rolling Process

Effects of Electropulsing Cutting on the Quenched and Tempered 45 Steel Rods

Static Electropulsing-Induced Microstructural Changes and Their Effect on the Ultra-Precision Machining of Cold-Rolled AZ91 Alloy

Electropulsing-induced Phase Transformations and Their Effects on the Single Point Diamond Turning of a Tempered Alloy AZ91

Effect of High-Density Pulsed Electric Current on the Formability of Aluminum Alloy

Effect of Electropulsing Treatment on Microstructure and Mechanical Properties of a Deformed ZrTiAlV Alloy

Effects of Electropulsing Treatment on the Precipitation Behaviour of Grain Boundary Carbides in GH3044 Alloy

Effect of Electropulsing Assisted Cutting Process on Cutting Properties of Quenched GCr15 Bearing Steel

Microstructural Modification and Mechanical Improvement of Ultrafine-Grained Ti Alloy Through Electron Wind Force: an Innovative Approach

Effect of Electropulsing on Grain Refinement of a Medium Carbon Low Alloy Steel

Characterization of Physical and Mechanical Properties of Tungsten Alloy Surfaces for Electroplasticity-Assisted Dry Cutting Machining

A Novel Electropulsing Treatment to Improve the Surface Strength and Repair the Pore of Additively Manufactured Ti-6Al-4V Alloy

Evolution of surface mechanical properties and microstructure of Ti-6Al-4V alloy induced by electropulsing-assisted ultrasonic surface rolling process

Application of High-Density Electropulsing to Improve the Performance of Metallic Materials: Mechanisms, Microstructure and Properties

Optimizing strength and ductility in 7150 Al alloys via rapid electropulsing cyclic heat treatment

Influence of Different Tool Polarity on Short Electric Arc Machining of GH4169

Effect of pulse current parameters on electroplastically assisted dry cutting performance of W93NiFe alloy

Effect of Electropulsing Treatment on the Microstructure and Superelasticity of TiNi Alloy

Superior Mechanical Properties of M35 High-Speed Steel Obtained by Controlling Carbide Precipitation and Distribution Via Electropulsing Treatment