Abstract:Titanium and its alloys (especially Ti6Al4V) are widely employed in aerospace and biomedical industry. Wire electric discharge machining is common in practice to machine this difficult-to-cut material. But owing to the thermo-electric nature of the process, it is challenging to have adequate level of surface integrity. This primary concern needs to be addressed as it mainly influences the surface mechanical characteristics. Therefore, the present research aims to address the aforesaid issues using well-known multipass strategy. Understanding the multipass process dynamics and requirements, the potentiality of brass wire diameters was comprehensively examined and explored during WEDM of Ti6Al4V. Considering higher cost, unavailability, environmental hazards, and straightness issues of novel zinc-coated wire electrodes, readily available brass wires provide a cheaper and widely acceptable solution to enhance surface integrity of machined parts if equivalent results can be somehow made possible. For that sake, three different brass wire diameters; 0.15 mm, 0.2 mm, and 0.25 mm have been considered to evaluate their impact on surface roughness, recast layer thickness, overcut, machined surface microhardness, and cutting speed using multipass cutting technique. Experimental results revealed that 0.15 mm uncoated brass wire can produce white layer result equivalent to Topas Plus X wire (Cu core-double Zn-rich layer coating) which outperformed among all zinc-coated wires used in previously published research. Moreover, among different diameter brass wires, surface roughness is improved by 25% using multipass cutting with 0.15 mm diameter in comparison to its counterparts. Scanning electron microscope (SEM) analysis depicts that the said combination reduces recast layer thickness from 39.04 μm to 14.6 μm (~ 1.5 times lesser value). In addition to that, smaller diameter (0.15 mm) provides the maximum cutting rate in rough cuts (which consume maximum machining time) and dimensional accuracy.

Characterization of Physical and Mechanical Properties of Tungsten Alloy Surfaces for Electroplasticity-Assisted Dry Cutting Machining

Effect of pulse current parameters on electroplastically assisted dry cutting performance of W93NiFe alloy

Optimization of Process Parameters on Surface Integrity in Wire Electrical Discharge Machining of Tungsten Tool YG15

Machining performance of micro-pit and micro-groove composite textured tools in tungsten alloy turning

Machining characteristics and optimization of 10CrNi3Mo alloy steel by WEDM

Mechanism and machinability in novel electroplastic-assisted grinding ductile iron

Influence of electrical parameters in electro discharge machining of tungsten heavy alloys on surface texture properties

Theoretical and numerical studies of surface microstructural transformation in ultrasonic elliptical vibration cutting tungsten heavy alloys

Effect of Technological Parameters on the Process Performance of Pure Al 2 O 3 Layer of Ni–Al 2 O 3 FGMs by Self-Induced EDM

Studies on the Surface of High-Performance Alloys Machined by Micro-Edm

Machinability and pulse characteristics of Ti-16Al-14Nb (α/β) alloy in wire-electric discharge machining process: A surface integrity study

Experiments of Ti6Al4V manufactured by low-speed wire cut electrical discharge machining and electrical parameters optimization

Effect of tool geometry and cutting parameters on surface quality and chip morphology of amorphous electroless nickel-phosphorus alloy in ultra-precision turning

Research on machining Technology of Electrospark-electrochemical Hybrid Energy Field with tungsten hole

An in-depth evaluation of surface characteristics and key machining responses in WEDM of aerospace alloy under varying electric discharge environments

Research status and development trend of tungsten alloy cutting

Effects of Electropulsing on the Machinability and Microstructure of GH4169 Superalloy During Turning Process

Surface Structure Evolution and Measurement Analysis of Ti6Al4V Titanium Alloy by Electric Arc Electrochemical Machining

Generation of surface texture on 2A50 aluminum alloy with electrochemical micromachining for tribological application

Investigation on the Micro-Structures and Properties of the P20 Steel Surface after Electrical Discharge Machining

Effect of Al7075 and Activated Carbon reinforced Composite on Optimizing WEDM Responses