Abstract:Two blends between polyamide 6 (PA6) and Polyamide 6co6T (PA6co6T, a random copolymer between polyamide 6 and polyamide 6T) were fabricated by melt-mixing on a twin-screw extruder and the subsequent injection molding, or through the in-situ polymerization of F-caprolactam in the presence of PA6co6T. As far as the former method is concerned, there exist an obvious decline of toughness and a slight increase in strength and modulus; however, for the latter, there appear a remarkable improvement in toughness and a simultaneous moderate increase in strength and modulus. A series of characterizations were carried out including scanning electron microscopy, wide-angle X-ray diffraction, polarized optical microscopy, differential scanning calorimetry, dynamic mechanical analysis, and Fourier transform infrared spectrometry. It is found that both blends exhibit single glass transition on DMA tan delta curves. However, contrary to that of the melt-mixed blends, the glass transition temperature (T-g) of the in-situ ones decreases with increasing PA6co6T content. It is suggested that different mixing levels are the main reasons. Moreover, the addition of PA6co6T containing linear rigid segments conducts remarkable refinement of spherulites for the blends. Significantly different changes in the crystallographic form, spherulite size, crystalline content and perfection due to the introduction of PA6co6T for the two blends are ascribed to their varied thermomechanical histories and the presence of interchange reaction only for the in-situ blends. On the basis of the characterizations of the microstructures, the different trends of changes in the mechanical properties with the addition of PA6co6T for the two fabrication methods are discussed. (C) 2007 Wiley Periodicals, Inc.

Preparation of a Structured Acrylic Impact Modifier and Its Application in Toughening Polyamide 6

Core-Shell Particles Of Poly(Methyl Methacrylate)-Block-Poly(N-Butyl Acrylate) Synthesized Via Reversible Addition-Fragmentation Chain-Transfer Emulsion Polymerization And The Polymer'S Application In Toughening Polycarbonate

Relationship between structure and properties in high-performance PA6/SEBS-g-MA/(PPO/PS) blends: The role of PPO and PS

Effect of Reactive Group Types on the Properties of Core-Shell Modifiers Toughened PA6

Toughening of Polyamide‐6 with Little Loss in Modulus by Block Copolymer Containing Poly(styrene‐alt‐maleic Acid) Segment

In Situ Formation of the Core–Shell Particles and Their Function in Toughening PA6/SEBS-g-MA/PP Blends

Toughening of PA6 with MAH Functionalized Acrylate-styrene-acrylonitrile Copolymer

Toughening Mechanism of Long Chain Branched Polyamide 6

Morphology and mechanical properties of Acrylonitrile-styrene-acrylate toughened plastics with block copolymer chain structure: Acrylonitrile-styrene-acrylate (ASA) toughened plastics with block copolymer chain structure

Preparation of Functionalized Core-Shell Structural Polymer with Methacrylic Acid and Modifying Nylon 6

Toughening Of Polyamide-6 With A Maleic Anhydride Functionalized Acrylonitrile-Styrene-Butyl Acrylate Copolymer

The Effect of Core–Shell Ratio of Acrylic Impact Modifier on Toughening PLA

Toughening of PA6 Nanocomposites by Reactive Acrylonitrile–butadiene–styrene Core–shell Rubber Particles

Construction of Core‐Shell Structure in PA6/ABS/SEBS Blends for Achieving Stiffness‐Toughness Balance

Blends of Poly(2,6-Dimethyl-1,4-Phenylene Oxide)/Polyamide 6 Toughened by Maleated Polystyrene-Based Copolymers: Mechanical Properties, Morphology, and Rheology

Influence of Preparation Methods on the Structures and Properties for the Blends Between Polyamide 6co6t and Polyamide 6: Melt‐mixing and In‐situ Blending

Preparation of Super Toughened PA 6/ABS Blend

Reactive Compatibilization and Elastomer Toughening of Poly(2,6-dimethyl-1,4-phenylene Oxide)/polyamide 6 Blends

Influence of the Rubber Crosslinking Density of A Core-Shell Structure Modifier on the Properties of Toughened Poly(Methyl Methacrylate)

Toughening of Pbt/Pc Blends with Epoxy Functionalized Core-Shell Modifiers

Toughening Effects of "Core-Shell" Particles in PA6/SEBS-g-MA/PPO Blends