Abstract:Fabricating chalcopyrite Cu(In,Ga)Se2 (CIGS) films from electrodeposition is one of the most effective ways to lower the production cost and energy consumption compared with that from vacuum methods. However, this process often produces a pronounced rough surface with impurity phases, induces the accumulation of gallium, and results in a low surface band gap. In this work, ammonium sulfide ((NH4)2S, AS) solution treatment is used as a single way to realize the optimization of the distribution of elements on the CIGS surface. It is revealed that this room-temperature process not only significantly reduces the surface roughness (Ra) but also incorporates sulfur (S) into the CIGS film successfully. An appropriate AS treatment duration can effectively remove the impurity phases and reduce the series resistance, and thus the dominant recombination moves from the CdS/CIGS heterojunction interface to the bulk. Consequently, the open-circuit voltage (VOC) and fill factor (FF) of solar cells have been greatly improved (from 484 to 532 mV, from 62.52 to 68.15%), leading to higher efficiency of 11.92%. This work focuses on revealing the etching mechanism of the CIGS films by the AS treatment at room temperature.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00220?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00220</a>.Best solar cell parameters of different unannealing samples (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00220/suppl_file/ae1c00220_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Fabrication of Cu(In,Ga)Se-2 Thin Films from Nanoparticles by Non-Vacuum Mechanochemical Method and Rapid Thermal Annealing Process

Increasing surface band gap of Cu(In,Ga)Se2 thin films by post depositing an In-Ga-Se thin layer.

Synthesis and Characteristics of Cu(In,Ga)Se2 Thin Films from Nanoparticles by Solvothermal Method and Selenisation Process

Preparation of Cu(In,Ga)Se2 Thin Film by Solvothermal and Spin-coating Process

Preparation of Cu(In,Ga)Se2 Thin Film by Non-Vacuum Mechanochemical and Spin-Coating Process

Preparation of Polycrystalline Cu(In,Ga)Se_2 Thin Film with Nano-metal Oxide:the Chemical Reaction Process and Its Properties

Fabrication of Cu(In, Ga)Se-2 Thin Films by Sputtering from A Single Quaternary Chalcogenide Target

Research progress on synthesis of CuIn 1-xGa xSe 2 nanoparticles

Synthesis and Characterization of CIGS Powder

Research progress on synthesis of CuIn1-x Gax Se2 nanoparticles

CIGS formation by high temperature selenization of metal precursors in H 2 Se atmosphere

Fabricating Cu(In,Ga)Se2 (CIGS) Thin Films with Large Grains Based on the Quaternary CIGS Targets

Preparation of High Quality CuIn1-xGaxSe2 Thin Films by Modified Selenization Procedure of Sequential Sputtering Metallic Precursors

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se2 Films by (NH4)2S Solution at Room Temperature

Fabrication of Cu(In,Ga)Se2 thin films solar cell by selenization process with Se vapor

Preparation of Cu(In,Ga)Se2 Thin Film by Sputtering from Cu(In,Ga)Se2 Quaternary Target

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se 2 Films by (NH 4 ) 2 S Solution at Room Temperature

Formation of CuInSe2 and Cu(In,Ga)Se2 films by electrodeposition and vacuum annealing treatment

Preparation and characterization of Cu(In, Ga)(Se, S)2 thin films by sulfurization of electrodeposited Cu(In, Ga) Se2

Fabrication of Homogeneous CIGS Thin Film by Plasma-Enhanced Se Vapor Selenization Coupled with Etching Process

Characterization and performance of Cu(In,Ga)Se2 thin films incorporating low-temperature pre-annealing process