Abstract:Fabricating chalcopyrite Cu(In,Ga)Se2 (CIGS) films from electrodeposition is one of the most effective ways to lower the production cost and energy consumption compared with that from vacuum methods. However, this process often produces a pronounced rough surface with impurity phases, induces the accumulation of gallium, and results in a low surface band gap. In this work, ammonium sulfide ((NH4)2S, AS) solution treatment is used as a single way to realize the optimization of the distribution of elements on the CIGS surface. It is revealed that this room-temperature process not only significantly reduces the surface roughness (Ra) but also incorporates sulfur (S) into the CIGS film successfully. An appropriate AS treatment duration can effectively remove the impurity phases and reduce the series resistance, and thus the dominant recombination moves from the CdS/CIGS heterojunction interface to the bulk. Consequently, the open-circuit voltage (VOC) and fill factor (FF) of solar cells have been greatly improved (from 484 to 532 mV, from 62.52 to 68.15%), leading to higher efficiency of 11.92%. This work focuses on revealing the etching mechanism of the CIGS films by the AS treatment at room temperature.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c00220?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c00220</a>.Best solar cell parameters of different unannealing samples (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c00220/suppl_file/ae1c00220_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Preparation and Characterization of Cu(In, Ga) (se, S)(2) Thin Films by Sulfurization of Electrodeposited, Cu(In,Ga)Se-2 Precursors

Increasing surface band gap of Cu(In,Ga)Se2 thin films by post depositing an In-Ga-Se thin layer.

Preparation And Characterization Of Cu(In,Ga)Se-2 Thin Films By Selenization Of Cu0.8ga0.2 And In2se3 Precursor Films

Cu(In,Ga)Se2-based Solar Cells Prepared from Se-containing Precursors

Cu(In, Ga)(S, Se)2 electrodeposition and characterizations using improved electrolytes

Influences of Sulfurization on Performances of Cu(In,Ga)(Se,S)2 Cells Fabricated Based on the Method of Sputtering CIGSe Quaternary Target

Growth and Characterization of Copper Indium Gallium Diselenide Films for Solar Cells Fabrication

Synthesis and Characterization of CIGS Powder

Metal Precursor with Bi-Layer Indium for Cu(In,Ga)Se2 Thin Film Preparation

Preparation of Cu(In,Ga)Se2 Thin Film by Sputtering from Cu(In,Ga)Se2 Quaternary Target

Preparation and Characterization of Cuins2 Thin Films for Solar Cells by Chemical Bath Deposition

Characterization of Cu(In,Ga)Se2 Films Deposited by Single-Step Electron Beam Evaporation for Solar Cell Applications

Enhancing Surface Properties for Electrodeposited Cu(In,Ga)Se 2 Films by (NH 4 ) 2 S Solution at Room Temperature

Surface evolution of sputtered Cu(In,Ga)Se 2 thin films under various annealing temperatures

Investigation of Cu(In,Ga)Se2 Polycrystalline Growth: Ga Diffusion and Surface Morphology Evolution

Preparation and Characterization of Cugas2 Thin Films As A Promising Parent Material for Intermediate Band Solar Cells

Effects of Annealing on CuInGaSe2 Solar Cell Prepared by Magnetron Sputtering

EFFECT OF ANNEALING ON THE CuInS2 THIN FILMS PREPARED BY CHEMICAL BATH DEPOSITION

Research progress on synthesis of CuIn1-x Gax Se2 nanoparticles

Investigation of Copper Indium Gallium Selenide Material Growth by Selenization of Metallic Precursors

Formation of CuInSe2 and Cu(In,Ga)Se2 films by electrodeposition and vacuum annealing treatment