Abstract:The corrosion behavior of functionally graded cemented carbide (FGCC), with CoNiCrFe binder (WC-CoNiCrFe), has been investigated by performing electrochemical measurements and chemical characterization. The results showed that the CoNiCrFe binder was selectively dissolved in alkaline and acidic solutions. In the NaOH solution, the high contents of Ni and Co generated a passive film consisting of Co(OH) 2 , Ni(OH) 2 , Co 3 O 4 , and NiO that effectively isolated the corrosive medium from the materials. However, the contents of Fe and Cr were too low to provide satisfactory protection. In the HCl solution, the Cr element generated Cr 0 , Cr 2 O 3 , and Cr(OH) 3 . However, the Cr content was too low to form a passive film. In addition, Co, Ni and Fe in the binder were selectively dissolved in the acidic solution. Moreover, compared with the FGCC, the non-graded cemented carbide (CC) had a higher binder content and a more dispersed WC distribution. Thus, it formed a denser and thicker passive film, which was beneficial for the corrosion resistance in the NaOH solution. However, the CoNiCrFe binder was severely corroded in the HCl solution, which was due to the absence of a passive film. In comparison, the FGCC with a lower binder content and a denser WC distribution, showed a higher corrosion resistance. On the other hand, the WC grain size showed the opposite effect in alkaline and acidic solutions. In the NaOH solution, a small WC grain size increased the number of WC/CoNiCrFe interfaces, which favored the formation of a dense passive film. It, thereby reduced the probability for pitting corrosion. In the HCl solution, the corrosion generally started from grain boundaries with high interface energy as no passive film existed. Thus, a large WC grain size facilitated the improvement of the corrosion resistance. The results from the present study do not only provide a theoretical guidance for an understanding of the anticorrosion mechanism of WC-CoNiCrFe, but also a new approach for the preparation of cemented carbides with high corrosion resistance.

Development of Research on WC-Ni Cemented Carbides of Mechanical Seal Face Materials

Enhanced the Mechanical Properties and Corrosion Resistance of Ultra-Coarse Grain WC-8Co Cemented Carbides by the Introduction of Cu and Ni

Wear phenomena on WC-based face seal rings

Preparation of Ultra-Fine WC-Co Cermet and Its Wear Behavior

Design for Manufacturing of Cemented Carbide Coated Components Toward High Wear and Impact Resistance Performance

Research On Wear Behavior Of Atc Cermet Material

Study on salt spray corrosion and friction wear performance of CrN coated cemented carbide sealing ring

Microstructure, mechanical and friction-wear properties of SiC-WC composite with Al and C as sintering aids

High-performance WC-AlCoCrFeNi 2.1 cemented carbides fabricated by resistance seam additive manufacturing

WC/Ni Cemented Carbide Coating and Its Wear Resistance Synthesized by Laser Powder Feeding Cladding

Investigation of the Machined Surface Integrity of WC-High-Entropy Alloy Cemented Carbide

Ultrafine WC-Ni cemented carbides fabricated by spark plasma sintering

Friction and wear behavior of cemented carbide self-matching pairs under different water lubrication conditions

Effect of WC grain size on mechanical properties and microstructures of cemented carbide with medium entropy alloy Co-Ni-Fe binder

Study on the abrasive resistance of Ni-based coatings containing WC hard phase

Dry Friction Properties of Diamond-Coated Silicon Carbide

First principles calculation of interfacial stability, electronic and mechanical properties of WC-304 cemented carbides

Research Progress on Friction and Corrosion Behavior of Mining Cemented Carbide

Microstructure and mechanical properties of WC–Co-based cemented carbide with bimodal WC grain size distribution

Microstructures and Properties of a Novel Cemented Carbide Prepared Using a Co–Ni–Cu Multiprincipal Element Alloy As the Binder

Corrosion behavior of functionally graded cemented carbides with CoNiCrFe binder