Abstract:In the present research an Al–7.7%Mn–4.9%Zr–3.2%Cu (wt%) alloy was processed by mechanical alloying (MA) followed by hot press sintering. The microstructure, phase composition, and mechanical properties of the MA granules and sintered samples were investigated. The dissolution of Mn, Zr, and Cu with further precipitation of the Al6Mn phase were observed during high-energy ball milling. In the alloy processed without stearic acid after milling for ~10 h, an Al-based solid solution with ~4.9 wt%Zr, ~3.2 wt%Cu and a ~5 wt%Mn with a grain size of ~16 nm and a microhardness of ~530 HV were observed. The addition of stearic acid facilitated Mn dissolution and precipitation of the Al6Mn phase during milling but led to the formation of the ZrH2 phase that decreased the Zr solute and the microhardness. Precipitation of the Al6Mn, L12–Al3Zr, and Al2Cu phases during annealing and sintering of the MA granules in the temperate range of 350–375 °C was observed, and an additional Al20Cu2Mn3 phase was precipitated at 400–450 °C. Hot-press sintering at 450 °C provided a low fraction of cavities of ~1.5%, the yield strength of 1100 MPa, ultimate compressive strength of 1200 MPa, strain at fracture of 0.5% at room temperature, the yield strength of 380 MPa, ultimate compressive strength of 440 MPa, and strain at fracture of 3.5% at 350 °C. The microstructural evolution during high-temperature deformation on the sample surface was studied and the differences in deformation behavior for the alloys sintered at different temperatures were discussed.

Mechanochemical decomposition of higher manganese silicides in the ball milling process

Effect of ball milling on the phase constitution and microstructure of induction melted Higher Manganese Silicides and their thermoelectric properties

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Grain Size Effect on the Phase Transformations of Higher Manganese Silicide Thermoelectric Materials: an in Situ Energy Dispersive X-Ray Diffraction Study

Hydriding/dehydriding properties of La2Mg16Ni alloy prepared by ball milling in different milling environments

Mechanical Ball Milling Preparation and Electrochemical Hydrogen Storage Properties of Amorphous Mg-Fe Composites

Effect of Mechanical Alloying on the Dissolution of the Elemental Mn and Al-Mn Compound in Aluminum

Microstructural Evolution During High Energy Ball Milling of Fe2o3-Sio2 Powders

Effect of mechanical milling on microstructure evolution and mechanical properties of Al–Zn–Mg–Cu–Si alloy fabricated via spark plasma sintering

Synthesis Mechanism of Amorphous Si2BC3N Powders: Structural Evolution of 2si‐bn‐3c Mixtures During Mechanical Alloying

Characterization of mechanochemical modification in SiC powder

Amorphization in the AlC System by Mechanical Alloying

Effect of Ball Milling Parameters on Properties of Nano-Sized Tungsten Powder via Mechanochemical Processing

Mechanosynthesis of molybdenum carbides by ball milling at room temperature

Mechanical properties of the Al-Mg/MWCNTs composite powders: The effects of ball milling process parameters

Microstructure and magnetic properties of MnBi powders prepared by various ball milling processes

Effect of high energy ball milling on the displacement reaction in particulate reinforced Al–Si–Cu alloy matrix composite powders

Mechanical milling/alloying of intermetallics

Effect of cyclic mechanical treatment on the final properties of Nb + 2Si powder mixtures prepared for SHS

The Microstructure and Properties of Al–Mn–Cu–Zr Alloy after High-Energy Ball Milling and Hot-Press Sintering

Effect of mechanochemical activation on surface oxidation of steel ball in milling serpentinite