Abstract:Mixed elemental powders, with a composition W-7 w/o Ni-3 w/o Fe and W-20 w/o Cu were mechanically alloyed (MA) using a high-energy ball mill. Small amounts of low-molecular-weight organic Substances (ethyl alcohol. stearic acid, polyethylene glycol, N,N-dimethylformamide) were used as process-control agents to decrease particle agglomeration, minimize contamination, and improve oxidation resistance and moldability. After 20-40 h of milling. ultrafine tungsten-base composite powders with a particle size similar to 0.3 pm were obtained in. which the tungsten crystallite size was 10-30 nm. The nanocrystalline powder was then sintered to near-ill density at temperatures above and below the solidus temperature of the transition-metal binder phase. Density and mechanical properties of the sintered samples were measured and microstructures characterized. For the milled W-20 w/o Cu nanocomposite powder. the compact sintered to near-full density (99% of the pore:free level), with good mechanical properties and a fine microstructure. The tensile strength was 700 MPa, elongation to fracture 5%, and the grain size was 1 mu m. In comparison, the conventional W-Cu composite had. low strength, no elongation and a coarse grain size. After liquid-phase sintering for 5-15 min. the milled W-Ni-Fe composite exhibited an excellent combination of tensile strength and elongation, and retained a uniform tungsten grain size similar to 3-5 mu m. The maximum tensile strength and elongation to fracture of the milled and sintered IV-Ni-Fe compact were 1, 150 MPa and 25%. respectively. In comparison with conventional materials, the grain size was about one order of magnitude smaller with attendant higher strength and ductility.

Effect of Ball Milling Parameters on Properties of Nano-Sized Tungsten Powder via Mechanochemical Processing

Long-term Ball Milling and Hot Pressing of In-Situ Nanoscale Tungsten Carbides Reinforced Copper Composite and Its Characterization

The effects of ball-milling treatment on the densification behavior of ultra-fine tungsten powder

The effect of trace nickel additive and ball milling treatment on the near-full densification behavior of ultrafine tungsten powder

Effect of Processing Parameters on the Formation Process of Nano-Sized ZrB2 Powders by the High Energy Ball Milling

Main Influential Factors of Preparing Nano-tungsten Powder Using High Energy Ball Mill

Mechanical Alloying Behavior of Nb–Ti–Si-based Alloy Made from Elemental Powders by Ball Milling Process

Preparation of Nanocrystalline Tungsten Powder and Study of Its Sinterability

STUDY ON PURE TUNGSTEN NANOCRYSTALLINE POWDERS PREPARED BY HIGH ENERGY BALL MILLING

Effect of ball milling on NiTi powder metallurgy alloy

Mechanical effect of Mo powder in ball milling process

Sintering Of Nanostructured Tungsten-Base Composites

Influence of Ball-milling on Sintered Body Density of Fine Tungsten Powder

Effect of Ball Milling Time on Microstructure and Properties of Nanocrystalline W-Cu Composite Powder

Synthesis of nanocrystalline cubic substoichiometric WC1 − z powders by mechanochemical technology

Synthesis and Characteristics of W-Ni-Fe Nano-Composite Powders Prepared by Mechanical Alloying

Study on the Main Promotion Factors of Powder Refinement in High-energy Ball Milling

Mechanical properties of the Al-Mg/MWCNTs composite powders: The effects of ball milling process parameters

Production Of Intermetallic Compound Powders By A Mechanochemical Approach: Solid-Liquid Reaction Ball Milling

Sub-micron MoC powders prepared by high-energy mechanochemistry method

Effect of Nanocrystalline Tungsten Powders on the Microstructure and Properties of Liquid-Phase Sintered 93W Alloys