Measured stopping power for 16O ions in Al, Cu and Ag foils

xiting lu,tao zheng,zonghuang xia,dingyu shen

DOI: https://doi.org/10.1016/S0169-4332(03)00936-X

IF: 6.7

2004-01-01

Applied Surface Science

Abstract:The stopping powers for 0.32–0.43MeV/A 16O ions in Al, Cu and Ag foils have been measured with the elastic recoil detection (ERD) method. The results are compared with the calculated values of SRIM2000 and previous experimental data.

What problem does this paper attempt to address?

Measured Stopping Powers for 1–6 MeV 7li Ions in C, Al, Cu, Ag, Au and Pb Foils and in a Thin Si Crystal

Z Li,ZY Zhou,GQ Zhao,JY Tang,FJ Yang

DOI: https://doi.org/10.1016/0168-583x(95)01532-9

1996-01-01

Abstract:Stopping powers for 1–6 MeV 7Li ions in C, Al, Cu, Ag, Au and Pb foils and in a thin Si crystal were measured in transmission geometry, with the uncertainties less than 6%. The measured data were compared with the available literature data and the values of TRIM-91 and TRIM-95, and the results were discussed in detail.
A New Method for Measuring Stopping Powers by Erd

XT LU,ZH XIA,KG ZHOU,CW JIN,XH YANG,HT LIU,DX JIANG,YL YE

DOI: https://doi.org/10.1016/0168-583x(91)95602-a

1991-01-01

Abstract:By elastic recoil detection (ERD) the stopping powers have been measured for F-19 and Cl-35 ions at energies from approximately 0.29 to approximately 0.42 MeV/nucleon in Ag films. The results are compared with the semiempirical values of TRIM 90 and previous experimental values.
Stopping power for MeV 12C ions in solids

Zheng Tao,Lu Xiting,Zhai Yongjun,Xia Zonghuang,Shen Dingyu,Wang Xuemei,Zhao Qiang

DOI: https://doi.org/10.1016/S0168-583X(97)00585-5

1998-01-01

Abstract:The stopping powers for 0.3–6.4 MeV 12 C ions in C, Al, Ti, Cu, Nb and Ag have been measured with the transmission method. The experimental data on stopping power are compared with evaluated values using LSS theory, ZBL semiempirical model predictions and previous experimental data. The results show that there is significant discrepancy between present work and LSS theory; for C in Al, ZBL calculations quite agree with our measurements, yet for C in other stoppers, those cannot reproduce most of present experimental data; our work consists mostly with previous measurements. Moreover, present stopping power data exhibit apparent Z 2 -oscillation.
Measured stopping power for 11 B ions in Z = 6 – 47 targets

Zheng Tao,Lu Xiting,Xia Zonghuang,Shen Dingyu

DOI: https://doi.org/10.1103/physrevb.57.10213

1998-01-01

Physical Review B - Condensed Matter and Materials Physics

Abstract:The stopping powers for 0.5-5.2 MeV 11B ions in the C, Al, Ti, Cu, Nb, and Ag targets have been measured using a transmission technique. The experimental error is about 3%. The results are compared to the TRIM-91 calculation and fitted to an empirical formula. Our measurements for 11B in the Al target are reasonably consistent with Ziegler's compilation. However, for the other five stoppers, significant deviation is found. The effective charge deduced from our experimental measurements appears to have a clear dependence on the stopping medium. The electronic stopping power at low energies exhibits a strong Z2 oscillation, which becomes weaker with increasing energy of boron ions.
Stopping Power of Au and Ag for He Ions

Xiaojing Huang,Xiting Lu,Changwen Jin,Chengfang Zhou,Yanlin Ye,Zonghuang Xia,Hongtao Liu,Dongxing Jiang

DOI: https://doi.org/10.1088/0256-307x/10/4/004

1993-01-01

Abstract:Energy loss of 0.45-5.0 MeV 4He ions in Au and Ag films were measured with the Rutherford backscattering method, and the stopping powers at lower energy range were extracted by comparing with that determined by Anderson et al. at higher energy range. Significant deviation between the experimental data and the semiempirical calculations by TRIM-90 appears around the stopping maximum. The accuracy of our results was expected to be ±1%.
Stopping Power of Compounds for 16 O and 19 F Ions

ZQ WU,XT LU,CW JIN,T ZHENG,ZH XIA,HT LIU,DX JIANG,YL YE

DOI: https://doi.org/10.1088/0256-307x/11/9/003

1994-01-01

Chinese Physics Letters

Abstract:The stopping powers of CaF2 and MoO3 for O-16 and F-19 were measured with heavy-substrate Rutherford backscattering technique. The present results are compared with the prediction of Bragg's rule, and strong deviation was observed. The experimental error is 5% or so.
Stopping power of Mylar for low-velocity 11B, 12C, and 16O ions.

jin changwen,lu xiting,huang xiaojing,ye yanlin,xia zonghuang,liu hongtao,jiang dongxing

DOI: https://doi.org/10.1103/physrevb.48.6858

1993-01-01

Abstract:The energy loss and stopping powers of 1.0--6.0 MeV $^{11}\mathrm{B}$, $^{12}\mathrm{C}$, and $^{16}\mathrm{O}$ ions in Mylar foil were determined in a transmission geometry. The experimental data were compared to the commonly used semiempirical theoretical predictions of Ziegler, Biersack, and Littmark and significant deviations were observed. The stopping powers were determined to an accuracy of 4%.
Evaluation of Stopping Powers of Superheavy Ions with $\it{Z}$ up to 124 in Al and U

Yong Hee Chung

DOI: https://doi.org/10.48550/arXiv.1502.00266

2015-02-01

Nuclear Experiment

Abstract:Electronic and nuclear stopping powers of superheavy ions with $\it{Z}$ up to 124 and $\it{A}$=300 in Al and U were estimated in the energy range of 0.01-0.20 MeV/u. The corresponding stopping powers were estimated using stopping powers of ions with 6$\leq$$\it{Z}$$\leq$92 obtained from SRIM. The results were compared with those deduced from Northcliffe and Schilling$'$s stopping-power tables and with experimental data for $^{16}$O and $^{19}$F ions in Al. Estimated electronic stopping powers of the light ions agreed better with their experimental values above 0.10 MeV/u than the SRIM data.
Stopping Power Of Mylar For Low-Velocity B-11, C-12, And O-16 Ions

Jin Changwen,Lu Xiting,Huang Xiaojing,Ye Yanlin,Xia Zonghuang,Liu Hongtao,Jiang Dongxing

DOI: https://doi.org/10.1103/PhysRevB.48.6858

IF: 3.7

1993-01-01

Physical Review B

Abstract:The energy loss and stopping powers of 1.0-6.0 MeV B-11, C-12, and O-16 ions in Mylar foil were determined in a transmission geometry. The experimental data were compared to the commonly used semiempirical theoretical predictions of Ziegler, Biersack, and Littmark and significant deviations were observed. The stopping powers were determined to an accuracy of 4%.
Stopping Powers of Bromine and Carbon in Silver

Changwen Jin,Xia Lu,Xia Zonghuang,Hongtao Liu,Dongxing Jiang,Yanlin Ye

DOI: https://doi.org/10.1088/0256-307x/8/12/003

1991-01-01

Chinese Physics Letters

Abstract:The stopping powers of Br and C in Ag film have been measured with the method of elastic recoil detection in energy range 0.28-0.42 MeV/amu. The results have been compared with the theoretical calculations of TRIM-90.
Stopping power for MeV energy Au ions in silicon 1 Supported by the Analytic and Measuring Foundatio

yongjun zhai,xiting lu,tao zheng,zonghuang xia,dingyu shen

DOI: https://doi.org/10.1016/S0168-583X(97)00586-7

1998-01-01

Abstract:The range distributions of Au ions with three implanted energies ( E i =1230, 2130, 3030 keV) in silicon were measured using Rutherford backscattering technique (RBS). The projected ranges were obtained and were larger than those of the TRIM-91 calculation. The nuclear stopping power S n calculated by Biersack general potential and the electronic stopping power S e = A ( E / E 0 ) P generated from LSS theory were used to fit the experimental data. Then the values of parameters A and P in the electronic stopping power formula S e = A ( E / E 0 ) P were determined. Significant discrepancies of the electronic stopping power between the experimental results and the TRIM-91 calculations were observed.
Stopping powers of LiF thin films deposited onto self-supporting Al foils for swift protons

Smail Damache,Djamel Moussa,Saad Ouichaoui

DOI: https://doi.org/10.48550/arXiv.2105.11539

2021-05-21

Instrumentation and Detectors

Abstract:The energy losses of ~(0.273-3.334) MeV protons in Lithium Fluoride thin films deposited by vacuum evaporation onto self-supporting Al foils have been measured using the transmission method. The thicknesses of selected and used Lithium Fluoride/Al target samples were accurately determined via systematic energy loss measurements for alpha particles from a very thin mixed 241Am/239Pu/233U radioactive source. The samples were investigated in detail for their stoichiometry and their impurity contents by backscattering Rutherford spectrometry and nuclear reaction analysis. Then, Lithium Fluoride stopping powers have been determined with overall relative uncertainty of less than 2.7% arising mainly from errors in the determination of target sample thicknesses. These S(E) data are reported and discussed in comparison to previous experimental data sets from the literature and to values calculated by the Sigmund-Schinner binary collision stopping theory both for molecular Lithium Fluoride and for the Lithium Fluoride compound assuming the Bragg's additivity rule. Our S(E) data show to be in excellent agreement with the latter theory for molecular Lithium Fluoride over the whole proton energy range explored, which supports the use of modified hydrogenic wave functions for evaluating atomic shell corrections in the case of low-Z2 target materials. In contrast, they exhibit a slightly increasing deviation from theoretical values derived for the Lithium Fluoride compound with assuming stopping force additivity as the proton energy decreases from ~400 Kev towards lower proton velocities.
Angular Distribution and Recoil Effect for 1mev Au+ Ions Through a Si3N4 Thin Foil

Ke Jin,Zihua Zhu,Sandeep Manandhar,Jia Liu,Chien-Hung Chen,Vaithiyalingam Shutthanandan,Suntharampillai Thevuthasan,William J. Weber,Yanwen Zhang

DOI: https://doi.org/10.1016/j.nimb.2014.02.093

IF: 1.279

2014-01-01

Nuclear Instruments and Methods in Physics Research Section B Beam Interactions with Materials and Atoms

Abstract:The Stopping and Range of Ions in Matter (SRIM) code has been widely used to predict nuclear stopping power and angular distribution of ion–solid collisions. However, experimental validation of the predictions is insufficient for slow heavy ions in nonmetallic compounds. In this work, time-of-flight secondary ion mass spectrometry (ToF-SIMS) is applied to determine the angular distribution of 1MeV Au ions after penetrating a Si3N4 foil with a thickness of ∼100nm. The exiting Au ions are collected by a Si wafer located ∼14mm behind the Si3N4 foil, and the resulting 2-dimensional distribution of Au ions on the Si wafer is measured by ToF-SIMS. The SRIM-predicted angular distribution of Au ions through the Si3N4 thin foil is compared with the measured results, indicating that SRIM slightly overestimates the nuclear stopping power by up to 10%. In addition, thickness reduction of the suspended Si3N4 foils induced by 1MeV Au ion irradiation is observed with an average loss rate of ∼107atoms/ion.
Stopping force of protons in Pt, Mo, and Cr foils at energies between 325 keV and 900 keV using the forward scattering method

C.B. Mtshali,Z.M. Khumalo,N Mongwaketsi,K. Segola,K. Lebesana,P. Sechogela,M. Msimanga

DOI: https://doi.org/10.1016/j.nimb.2024.165363

2024-04-19

Abstract:In this work, the stopping force of protons in Pt, Mo, and Cr foils was measured at energies between 325 and 900 keV using the forward scattering method. Obtained results were compared with predictions from the semi-empirical code SRIM, the purely theoretical code DPass, and shellwise local plasma approximation with Levine-Mermin dielectric function (SLPA-LM). Both theoretical predictions underestimate experimental data for Pt at the energies measured. However, the theoretical calculation results for Mo, and Cr displayed good agreement with experimental data over the measured energy range. The obtained results were also compared with data from the literature, which displayed experimental discrepancies, especially for Pt and Cr stopping while a very good agreement between all experimental data was observed for Mo data.

physics, nuclear, atomic, molecular & chemical,nuclear science & technology,instruments & instrumentation
Energy Straggling Measurements of 16 O and 19 F Ions in Au and CaF 2

Zeqing Wu,Xiting Lu,Changwen Jin,Tao Zheng

DOI: https://doi.org/10.1088/0256-307x/11/10/004

1994-01-01

Chinese Physics Letters

Abstract:Energy stragglings of 16O and 19F were measured with heavy-substrate Rutherford backscattering technique. Great deviation was observed between present data and Bohr's prediction. The accuracy of present experiment is about 10%.
Determination of Electron Inelastic Mean Free Path and Stopping Power of Hafnium Dioxide

J. M. Gong,K. Tokesi,X. Liu,B. Da,H. Yoshikawa,S. Tanuma,Z. J. Ding

DOI: https://doi.org/10.1016/j.rinp.2023.106609

IF: 4.565

2023-01-01

Results in Physics

Abstract:We present inelastic mean free path (IMFP) and stopping power data of the hafnium dioxide applying the relativistic dielectric response theory. The energy loss function (ELF) derived from reflection electron energy loss spectroscopy spectrum with the reverse Monte Carlo method was used for the first time to obtain the IMFP and stopping power of HfO2. The probability of the energy loss is determined by the dielectric response function εq,ω as a function of the frequency ω and the wavenumber q of the electromagnetic disturbance. Two algorithms, namely the full Penn algorithm (FPA) and the super-extended Mermin algorithm (SMA), were employed to expand the optical energy loss function, Im-1/ε0,ω, into the q,ω-plane. The results indicate that the IMFP and the stopping power obtained by using both algorithms are consistent at high electron energies, but show differences at low electron energies (less than ∼ 70 eV). This discrepancy arises from the consideration of the finite plasmon lifetimes effect in the SMA model, while it is neglected in the FPA model. Additionally, we observed that the band gap has a significant influence on the IMFP and the stopping power at low electron energies. Typically, the inclusion of the band gap leads to an increase in the IMFP, because transition channels with energies larger than E-Eg-Ev are prohibited.
Energy-Loss And Stopping Power Of He-4 Ions In Mylar Foils

Changwen Jin,Xiting Lu,Xiaojing Huang,Yanlin Ye,Zonghuang Xia,Hongtao Liu,Dongxing Jiang

DOI: https://doi.org/10.1088/0256-307X/11/4/003

1994-01-01

Chinese Physics Letters

Abstract:The energy loss and stopping power of He-4 ions in mylar foils were determined in a transmission geometry. The experimental stopping power data were compared to the previous measurements at higher energies. At lower energies, no previous measurements exist. The present results were also compared to the commonly used semiempirically theoretical predictions by Ziegler and Manoyan, and significant deviations were observed.
Measured Stopping Powers of 7 Li Ions in Silicon Single Crystal at 1-5 MeV

Z Li,GQ Zhao,ZY Zhou,JY Tang,FJ Yang

DOI: https://doi.org/10.1088/0256-307x/13/3/004

1996-01-01

Abstract:Stopping powers of 7Li ions in silicon single crystal at 1-5 MeV in random and channeling directions were determined in transmission geometry, with the uncertainties less than 6%. The measured results were compared with the available literature results and the values of TRIM-91 and TRIM-95.
Stopping powers and energy loss straggling for MeV protons in a kapton polyimide thin film

S. Damache,S. Djaroum,S. Ouichaoui,L. Amari,D. Moussa

DOI: https://doi.org/10.48550/arXiv.1709.06083

2017-09-18

Abstract:The energy loss and energy loss straggling widths have been measured in transmission for MeV protons traversing a thin kapton polyimide foil. In a prior step, the thickness and non-uniformity of the target foil were carefully investigated. The overall relative uncertainties in the stopping power and energy loss straggling variance data amount, respectively, to less than 2% and 8%. The experimental data show to be in excellent agreement with available previous ones and with those compiled in the ICRU-49 report. They are fully consistent with the predictions of Sigmund-Schinner's binary collision theory of electronic stopping over the whole proton energy range explored. An average deviation of ~2.5% relative to values calculated by the SRIM-2008 code, likely due to effects of valence electrons involving the , and bonds, is however observed at low proton velocities. The measured energy loss straggling data, which are unique to our knowledge, are found to be in good agreement with values derived by the classical Bohr formula for keV but they significantly exceed Bohr's collisional energy loss straggling at lower proton velocities where target electrons can no longer be considered as free. They also show to be consistent with the predictions of the Bethe-Livingston and Sigmund-Schinner theories over the low proton velocity region ( keV). However, they are significantly overestimated by these theories over the intermediate and high proton velocity regions, which may be due to bunching effect by inner shell electrons of the polymer target. Besides, our energy loss straggling data are in better overall consistency with the Yang, O'Connor and Wang empirical formula for keV, while deviations above the latter amounting up to ~18% are observed at lower proton velocities. Keywords: Swift protons; Kapton polyimide; Stopping power; Energy loss straggling; Binary collision theory.

Instrumentation and Detectors,Nuclear Experiment
Energy Loss and Stopping Power of <sup>4</sup> He Ions in mylar Foils

Changwen Jin,Xiting Lu,Xiaojing Huang,Yanlin Ye,Zonghuang Xia,Hongtao Liu,Dongxing Jiang

DOI: https://doi.org/10.1088/0256-307x/11/4/003

1994-01-01

Chinese Physics Letters

Abstract:The energy loss and stopping power of 4He ions in mylar foils were determined in a transmission geometry. The experimental stopping power data were compared to the previous measurements at higher energies. At lower energies, no previous measurements exist. The present results were also compared to the commonly used semiempirically theoretical predictions by Ziegler and Manoyan, and significant deviations were observed.

Measured stopping power for 16O ions in Al, Cu and Ag foils

Measured Stopping Powers for 1–6 MeV 7li Ions in C, Al, Cu, Ag, Au and Pb Foils and in a Thin Si Crystal

A New Method for Measuring Stopping Powers by Erd

Stopping power for MeV 12C ions in solids

Measured stopping power for 11 B ions in Z = 6 – 47 targets

Stopping Power of Au and Ag for He Ions

Stopping Power of Compounds for 16 O and 19 F Ions

Stopping power of Mylar for low-velocity 11B, 12C, and 16O ions.

Evaluation of Stopping Powers of Superheavy Ions with $\it{Z}$ up to 124 in Al and U

Stopping Power Of Mylar For Low-Velocity B-11, C-12, And O-16 Ions

Stopping Powers of Bromine and Carbon in Silver

Stopping power for MeV energy Au ions in silicon 1 Supported by the Analytic and Measuring Foundatio

Stopping powers of LiF thin films deposited onto self-supporting Al foils for swift protons

Angular Distribution and Recoil Effect for 1mev Au+ Ions Through a Si3N4 Thin Foil

Stopping force of protons in Pt, Mo, and Cr foils at energies between 325 keV and 900 keV using the forward scattering method

Energy Straggling Measurements of 16 O and 19 F Ions in Au and CaF 2

Determination of Electron Inelastic Mean Free Path and Stopping Power of Hafnium Dioxide

Energy-Loss And Stopping Power Of He-4 Ions In Mylar Foils

Measured Stopping Powers of 7 Li Ions in Silicon Single Crystal at 1-5 MeV

Stopping powers and energy loss straggling for MeV protons in a kapton polyimide thin film

Energy Loss and Stopping Power of <sup>4</sup> He Ions in mylar Foils