Reply to “Comments on ‘A Novel Broadband Printed Dipole Antenna With Low Cross-Polarization’”

Shiwen Yang,Zhanwei Zhou,Zaiping Nie

DOI: https://doi.org/10.1109/TAP.2008.922894

2008-01-01

Abstract:The authors reply to comment (by Holzman, 2008) on the original paper by Zhou et al. (2007).

What problem does this paper attempt to address?

Reply to “comments on ‘A Novel Broadband Printed Dipole Antenna with Low Cross-Polarization’”

Shiwen Yang,Zhipeng Zhou,Zaiping Nie

DOI: https://doi.org/10.1109/tap.2008.922894

IF: 5.7

2008-01-01

IEEE Transactions on Antennas and Propagation

Abstract:The authors reply to comment (by Holzman, 2008) on the original paper by Zhou et al. (2007).
A Novel Broadband Printed Dipole Antenna with Low Cross-Polarization

Zhanwei Zhou,Shiwen Yang,Zaiping Nie

DOI: https://doi.org/10.1109/tap.2007.908570

IF: 5.7

2007-01-01

IEEE Transactions on Antennas and Propagation

Abstract:A novel broadband printed dipole antenna with low cross-polarization is presented. The printed dipole employs a double-layered structure where the E-field component perpendicular to the dipole arms is minimized, thus low cross-polarization is obtained. Measurement results show that the printed dipole antenna achieves a bandwidth up to 50% while reducing the cross-polarization level to less than -30 dB within the frequency band.
A COMPACT DUAL-POLARIZED BROADBAND ANTENNA WITH HYBRID BEAM-FORMING CAPABILITIES

H. -L. Peng,W. -Y. Yin,J. -F. Mao,D. Huo,X. Hang,L. Zhou

DOI: https://doi.org/10.2528/pier11042905

2011-01-01

Abstract:A broadband dual-polarized four-port (DPFP) antenna is presented in this paper, which consists of a radiation element and a feed network. It is very compact in size, with the diameter of 150.0 mm and the height of 47.0 mm, with the following unique properties: (1) it has hybrid beam-forming capability and operates at two modes, which depends on its excitation; (2) its operating frequency range is from 0.96 to1.78 GHz, and the return loss is about 10 dB; (3) its insertion loss is (3 +/- 0.5) dB, with its balanced power splitting over the relative bandwidths of 37% at Mode 1 (180 degrees +/- 5 degrees phase shifting) and 55% at Mode 2 (+/- 5 degrees phase shifting), respectively; (4) an isolation of 30 dB at Mode 1 is obtained between the dual polarized ports, with the gain of 7.6 dBi and 42 degrees of the 3 dB-bandwidth at 1.25 GHz; and (5) the gain difference between Modes 1 and 2 is about 7 dB, within the angle of -15 degrees <= theta <= 15 degrees for the same polarization at 1.25 GHz. For the application of DPFP, a hybrid beam forming algorithm is proposed with an angular precision of 7 degrees and is validated by measurement.
Reply to "comments on 'the Foster Reactance Theorem for Antennas and Radiation Q'"

Wen Geyi

DOI: https://doi.org/10.1109/tap.2007.891878

IF: 5.7

2007-01-01

IEEE Transactions on Antennas and Propagation

Abstract:Presents a reply to the comment by Andersen and Berntsen (IEEE Trans. Antennas Propag., vol.55, no.3, pt.II, p.1013-14, March 2007) on the original paper by Geyi et al. (IEEE Trans. Antennas Propag., vol.48, p.401-8, 2000)
Design of an S-band Broadband Low Cross-Polarization Printed Dipole Array Antenna

ZHOU Zhan-wei,YANG Shi-wen,NIE Zai-ping

DOI: https://doi.org/10.3969/j.issn.1005-0388.2008.02.017

2008-01-01

Abstract:A novel broadband printed dipole antenna with low cross-polarization is proposed in this paper. The antenna employs a double-layered printed dipole with integrated balun structure, which retains the broadband characteristics while reducing the cross-polarization level. An S-band 16-element printed dipole array antenna is then formed, and the measured results indicate that the bandwidth of the array is up to 50%, while the cross-polarization level is less than -43 dB. Measurement results verified the broadband and low cross-polarization properties of the antenna array.
Author's Reply by S. Wang and F. L. Teixeira

Shumin Wang,F.L. Teixeira

DOI: https://doi.org/10.1109/lmwc.2004.827862

IF: 3

2004-01-01

IEEE Microwave and Wireless Components Letters

Abstract:Wang and Teixeira reply to a comment (by An Ping Zhao, IEEE Microwave Wireless Comp. Lett., vol.14, no.5, p. 248-9, 2004) on their original paper (Wang and Teixeira, IEEE Microwave Wireless Comp. Lett., vol.13, p.72-4, 2003 February).
Comment on “A Wideband Ultrathin Low Profile Metamaterial Microwave Absorber”

Dou Tian,Hongyu Shi,Anxue Zhang

DOI: https://doi.org/10.1002/mop.29897

IF: 1.311

2016-01-01

Microwave and Optical Technology Letters

Abstract:In A Wideband Ultrathin Low Profile Metamaterial Microwave Absorber published in the 57th volume of Microwave and Optical Technology Letters, the authors come to the conclusion that the proposed structure can realize a broadband absorber, which we cannot agree with. In our opinion, it should be cross-polarization reflection rather than absorption. (c) 2016 Wiley Periodicals, Inc. Microwave Opt Technol Lett 58:1773-1774, 2016
A Novel Broadband Dual-Polarization Antenna Utilizing Strong Mutual Coupling

Zengdi Bao,Zaiping Nie,Xianzheng Zong

DOI: https://doi.org/10.1109/tap.2013.2287010

IF: 5.7

2014-01-01

IEEE Transactions on Antennas and Propagation

Abstract:A novel broadband dual-polarization antenna utilizing strong mutual coupling with high isolation is presented in this communication. The antenna is composed of two orthogonally situated dipoles which have square-loop shape arms (SLSAs). And to shape the radiation pattern of the antenna, a metal reflector is placed under the antenna. By elaborately utilizing the strong mutual coupling between the two dipoles, very good impedance match and sufficiently high isolation can be achieved simultaneously, the reasons for which are analyzed in this communication. Both the simulated and the measured results show that a more than 57.5% impedance bandwidth with SWR<1.5 and port-to-port isolation >31 dB can be achieved for the proposed antenna. As an important advantage, the input impedance of the antenna can be controlled within certain limits by adjusting the configurations, thus the antenna can be fed directly by coaxial cables without using impedance transformers. Besides, the antenna structure is compact and simple.
Novel Ultrawide-Band Wide Beam Circular Polarization Antenna

ZHONG Ling-ling,QIU Jing-hui,BAI Wen-jing,WANG Nan-nan

DOI: https://doi.org/10.3321/j.issn:0367-6234.2007.05.016

2007-01-01

Abstract:A novel antenna is proposed.Four circular disc monopoles are placed across each other.The improved antenna is not only favorable for satisfying ultrawide-band return loss requirement but also advantageous in realizing the wide beams and good circular polarization performance within the beams.Analyses are conducted to determine the novel antennas' properties.The return loss,radiation patterns,axial ratio,gain and the time domain performance of the antennas are discussed detailedly.The analytic results verify that the novel circular disc monopole ultrawide-band antenna has reliable ultrawide-band performance during realizing wide beam and circular polarization.The novel antenna proposed in this paper is suitable for the wireless,satellite and mobile communication systems with good prospects.
Design and Discussion of a Broadband Cross-Dipole with High Isolation and Low Cross-Polarisation Utilising Strong Mutual Coupling

Zengdi Bao,Xianzheng Zong,Zaiping Nie,Shiwen Yang

DOI: https://doi.org/10.1049/iet-map.2013.0440

2014-01-01

Abstract:A broadband cross-dipole with high isolation and low cross-polarisation for base station applications in mobile wireless communications is presented in this study. By skillfully utilising the strong mutual coupling between the two dipoles, very good impedance match, sufficiently high isolation and low cross-polarisation can be achieved simultaneously. The measured results show that a more than 54% impedance bandwidth for standing wave ratio (SWR) < 1.5 from 1.695 to 2.95 GHz is achieved, within which the isolation is larger than 35 dB and the cross-polarisation is less than -34 dB. As a desirable advantage, the input impedance of the antenna can be changed within certain limits by properly adjusting the configuration, thus the antenna can be fed directly by 50-omega coaxial cables without the aid of impedance transformers. Particularly, besides the designing and the optimising work, the mechanisms for high isolation and low cross-polarisation as well as the method to adjust the input impedance are also discussed from a new point of view, which are also appropriate for other cross-dipole with the similar patterns.
A novel dual choke slot dual-polarization array antenna with low sidelobe

Changhong SONG,Qun WU,Wenjing ZHANG,Zhiyong LU

DOI: https://doi.org/10.13443/j.cjors.2013.05.018

2013-01-01

Abstract:A novel dual-polarization array antenna with low sidelobe is designed. The element antennas use pyramid horns, which realize dual-polarization radiation by orthogonal feed probes in different layers, and solve the problem of wide beam with low sidelobe by using dual choke slot. In the design of array feed, Taylor weighting is realized by using air coaxial line network, and reversed-phase feeding technique is used to improve the performance such as polarization isolation and cross polarization. The measured results indicate that the return loss is less than -35 dB at 9.5 GHz±500 MHz, the sidelobe level is less than -26 dB in the Azimuth and elevation patterns, the polarization port isolation is less than -30 dB, and the cross polarization level is less than -35 dB. Copyright © 2013 by Editorial Department of Chinese Journal of Radio Science.
Analysis of a Novel Ka Horn Antenna with Low Cross-Polarization

Y. -Z. Liu,S. Xiao,B. -Z. Wang

2013-01-01

Abstract:A Ka combined horn antenna with low cross-polarization is presented in this paper. The antenna consists of an edge-slotted waveguide linear array, a metallic-grid plane in the horn throat and a horn. The effects of metallic-grid and single-ridged waveguide to the cross-polarization are analyzed. Three kinds of 62-element Taylor linear array at Ka band are fabricated and measured and the measured cross-polarization level is less than -35dB in operating bandwidth. The proposed antennas are benefit for fabrication and fixation with low cross-polarization and can be extensively used in radar and communication systems.
Authors' response (Comments on "Scan impedance for an infinite dipole array: Hansen's formulas compared with Ansoft HFSS simulations")

S. Makarov,A. Puzella

DOI: https://doi.org/10.1109/MAP.2008.4656679

2008-02-01

Abstract:The authors reply to comments by M. Jones and S. Ortiz (see ibid., vol.50, no.1, p.188-191, February 2008). For the authors' original article see ibid., vol.49, no.4, p.143-156, August 2007.

Engineering,Physics
Comment on "Signal Correlation Between Two Normal- Mode Helical Antennas for Diversity Reception in a MultipathEnvironment

Xin Li,Zaiping Nie

DOI: https://doi.org/10.1109/TAP.2005.851798

2005-01-01

Abstract:This comment points out an inaccurate formula relating the signal correlation coefficient to the mutual impedance and corrects it.
Comment on "focusing of High Polarization Order Axially-Symmetric Polarized Beams" [chin. Opt. Lett. 7, 938 (2009)]

Lifeng Li

DOI: https://doi.org/10.3788/col20100811.1110

IF: 2.56

2010-01-01

Chinese Optics Letters

Abstract:Some mathematical and conceptual errors contained in a recent letter [Chin. Opt. Lett. 7, 938 (2009)] are pointed out.
A Broadband Dual-Polarized Printed Dipole Antenna With Low Cross-Polarization And High Isolation For Base Station Applications

Deqiang Yang,Sihao Liu,Zhiqin Zhao

DOI: https://doi.org/10.1002/mop.30467

IF: 1.311

2017-01-01

Microwave and Optical Technology Letters

Abstract:A dual-polarized dipole antenna with low cross-polarization and high isolation characteristics is presented. The proposed antenna is composed of three basic structures, i.e., a horizontal rectangular ground plate, four vertical plates with two rectangular patches on each of them, and a horizontal substrate with eight triangle patches. Every two vertical plates are put back-to-back which forms a double-layered structure. Thus the transverse E-field of the double-layered structure is significantly reduced because of this symmetric treatment, which gives rise to very low cross-polarization. Then the two double-layered structures are orthogonally arranged, generating dual polarizations. Simulated and measured results show that the proposed antenna realizes an impedance bandwidth of 47% (VSWR< 1.5), ranging from 1.8 to 2.9 GHz. The isolation between the two orthometric ports is higher than 30 dB across the bandwidth. Furthermore, the cross-polarization is -35 dB over the bandwidth. This antenna has the advantages of high isolation, low cross-polarization, and wide bandwidth. (C) 2017 Wiley Periodicals, Inc.
A Novel Aperture Coupled Microstrip Antenna Array with Low Cross-Polarization, Low Sidelobe and Backlobe

J Xiao,G Dong,MH Zhu

DOI: https://doi.org/10.1109/icmmt.2004.1411503

2004-01-01

Abstract:An aperture coupled microstrip antenna array with low cross-polarization, low sidelobe and backlobe is presented in the paper. The low cross-polarization (-35.1 dB) and low back radiation are achieved by using aperture-coupled configuration with the reflector ground. A good match feed network design enables the good bandwidth and low sidelobe lever (-20.9dB).
A Novel Broadband Dual-Polarization Antenna with High Isolation

Zengdi Bao,Zaiping Nie,Xianzheng Zong

DOI: https://doi.org/10.1109/aps.2013.6711312

2013-01-01

Abstract:A novel broadband dual-polarization antenna composed of two orthogonal dipoles with high isolation is presented in this paper. Due to properly utilizing the strong regional mutual coupling between the two dipoles, a very good impedance matching and a sufficiently high isolation can be achieved simultaneously, the reasons for which will be explained at the conference. The measured results show that it has a 53.7% impedance bandwidth of 1.65GHz-2.86GHz with VSWR < 1.5 and isolation < 32dB. As an important advantage, the input impedance of the antenna can be well controlled within certain limits by adjusting the configuration, thus the antenna can be fed directly by coaxial cables without using impedance transformers or other feeding circuits. Besides, it has a simple and compact configuration.
Reply to Comments on "Stored energies and radiation Q"

Wen Geyi

DOI: https://doi.org/10.1109/TAP.2016.2597639

2015-09-24

Abstract:It will be shown that the comment [1] contains numerous errors, misconceptions, inaccuracies, false assumptions, misunderstandings and unjustified claims. The analysis of the comment is built on a false assumption that the terminal current of an antenna fed by a waveguide is independent of frequency. This false assumption arises from the misunderstandings on the basic theory of transmission lines and misconceptions of normalization for a linear system. As a result, all the equations obtained from the assumption in the comment are incorrect, and the related discussions are untruthful. The delta gap source modeling has been abused in the comment, and this is reflected in the numerical results in the comment that give rise to negative stored energy. The main results of the commented paper have been misinterpreted by the authors of the comment, and the related analysis is established on illogical reasoning. The comment fails to pinpoint any errors in the commented paper. Instead, it reveals that the main results obtained by the authors of the comment in their previous publication [2] are incorrect.

Classical Physics
A CPW-Fed Broadband Quasi-Yagi Antenna with Low-polarization Performance

Xiaolin Xue,Guangjun Wen,Yuanhua Sun,Haobin Zhang

2015-01-01

Abstract:This paper proposes a uniplanar quasi-yagi antenna with the coplanar waveguide feedline. A novel driver dipole is proposed to expand the working frequency band of the antenna. Due to the unique driver dipole, the proposed quasi-yagi antenna can work from 3.75-10.4 GHz with low cross polarization performance at the same time. To verify the design, a prototype antenna is fabricated. The experimental results are in accordance with the simulation results very well.

Reply to “Comments on ‘A Novel Broadband Printed Dipole Antenna With Low Cross-Polarization’”

Reply to “comments on ‘A Novel Broadband Printed Dipole Antenna with Low Cross-Polarization’”

A Novel Broadband Printed Dipole Antenna with Low Cross-Polarization

A COMPACT DUAL-POLARIZED BROADBAND ANTENNA WITH HYBRID BEAM-FORMING CAPABILITIES

Reply to "comments on 'the Foster Reactance Theorem for Antennas and Radiation Q'"

Design of an S-band Broadband Low Cross-Polarization Printed Dipole Array Antenna

Author's Reply by S. Wang and F. L. Teixeira

Comment on “A Wideband Ultrathin Low Profile Metamaterial Microwave Absorber”

A Novel Broadband Dual-Polarization Antenna Utilizing Strong Mutual Coupling

Novel Ultrawide-Band Wide Beam Circular Polarization Antenna

Design and Discussion of a Broadband Cross-Dipole with High Isolation and Low Cross-Polarisation Utilising Strong Mutual Coupling

A novel dual choke slot dual-polarization array antenna with low sidelobe

Analysis of a Novel Ka Horn Antenna with Low Cross-Polarization

Authors' response (Comments on "Scan impedance for an infinite dipole array: Hansen's formulas compared with Ansoft HFSS simulations")

Comment on "Signal Correlation Between Two Normal- Mode Helical Antennas for Diversity Reception in a MultipathEnvironment

Comment on "focusing of High Polarization Order Axially-Symmetric Polarized Beams" [chin. Opt. Lett. 7, 938 (2009)]

A Broadband Dual-Polarized Printed Dipole Antenna With Low Cross-Polarization And High Isolation For Base Station Applications

A Novel Aperture Coupled Microstrip Antenna Array with Low Cross-Polarization, Low Sidelobe and Backlobe

A Novel Broadband Dual-Polarization Antenna with High Isolation

Reply to Comments on "Stored energies and radiation Q"

A CPW-Fed Broadband Quasi-Yagi Antenna with Low-polarization Performance