Abstract:Spinel LiMn2O4 has the advantages of high voltage, high safety, low pollution, low cost, and rich resources. However, its low initial capacity, rapid-cycle decay, and other factors hinder its commercialization process. In this paper, a pure phase LiMn2O4 is synthesized by a high-temperature solid-phase method, and the element doping is used to modify it to improve its cycle performance. The results show that the optimal process conditions for preparing LiMn2O4 are: the Li/Mn ratio is 1.05:2, the calcination temperature is 780°C, and the calcination time is 15 hours. X-ray diffractometer reveals that the samples prepared by Al3+ and F− co-doping are still typical spinel structures. Scanning electron microscope shows that the sample is single-crystal Li1.05Al0.02Mn1.98F0.02O3.98 with uniform grain distribution and regular morphology. The sample has excellent cycle performance, and its initial discharge specific capacity is 115.5 mAh g−1 at 0.1C. The capacity retention rate is still above 80% after 367 cycles, and the specific capacity is 90.3 mAh g−1. The Al-F co-doped LiMn2O4 single-crystal material can effectively inhibit the Jahn-Teller effect, alleviate the dissolution of Mn, as well as increase the diffusion channel of Li+. This work provides a theoretical basis for promoting the development of LiMn2O4 cathode materials for lithium-ion batteries.

Characterization of a New Spinel Li–Cr–Mn–O for Secondary Lithium Batteries

Preparation of Submicrocrystal LiMn2O4 Used Mn3O4 As Precursor and Its Electrochemical Performance for Lithium Ion Battery

Electrochemical Studies of Substituted Spinel LiAlyMn2−yO4−zFz for Lithium Secondary Batteries

The study of quaternary spinel phase Li-M-Mn-O (M = Ni, Cr, Mo, V) cathode

Preparation of Li1+Y-Xznxmn2-Yo4 Spinel As A Cathode Material for Li+-Batteries

Optimization Of Spinel Li1+Xmn2-Yo4 As A 4 V Li-Cell Cathode In Terms Of A Li-Mn-O Phase Diagram

Synthesis and Electrochemical Properties of Sc-Doped Li1.05scxmn2-Xo4 Spinel As Cathodic Material for Rechargeable Li-Battery

Studies of spinel LiCrxMn2−xO4 for secondary lithium battery

Optimization of Spinel Li[sub 1+x]Mn[sub 2−y]O[sub 4] as a 4 V Li-Cell Cathode in Terms of a Li-Mn-O Phase Diagram

Lithium Manganese Spinel Cathodes for Lithium‐Ion Batteries

Synthesis of Spinel Limn2o4 for Li-Ion Batteries Via Sol-Gel Process

Dependence of Battery Performance of Spinel Li{sub 1+x}mn{sub 2}o{sub 4} on the Preparation Method

Studies on LiMnO spinel system (obtained from melt-impregnation method) as a cathode for 4 V lithium batteries Part II. Optimum spinel from γ-MnOOH

Studies on an LiMnO Spinel System (obtained by Melt-Impregnation) As a Cathode for 4 V Lithium Batteries Part 1. Synthesis and Electrochemical Behaviour of LixMn2O4

Spinel Li1 + Xmn2o4 Synthesized by Coprecipitation As Cathodes for Lithium-Ion Batteries

Synthesis and Electrochemical Performance of LiNi0.5Mn1.5O4 Spinel Compound

Preparation of Spinel LiMn_2O_4 Cathode Materials for Li-ion Batteries Based on Sol-gel Process

Development of Spinel Limn2o4 for Positive Electrode Material of Li-Ion Batteries

Preparation and electrochemical properties of Al‐F co‐doped spinel LiMn 2 O 4 single‐crystal material for lithium‐ion battery

Research Development on Spinel Lithium Manganese Oxides Cathode Materials for Lithium-Ion Batteries

Defect Spinel Li8n/N+4mn8/N+4o4 Cathode Materials For Solid-State Lithium-Polymer Batteries