Abstract:Two kinds of spinel structure lithium manganese oxides obtained by a melt-impregnation method were examined in a lithium nonaqueous cell. The first type shows a voltage profile of a typical spinel electrode with the characteristic two-step process, which delivers a larger capacity, but fading capacity on cycling (type I). The other type delivers a slightly lower capacity and has ideal rechargeability with a quasi-one-step process (type II). The mechanism of the lithium ion insertion into the spinel compound was studied by several physical and chemical methods (differential chronopotentiometric curves, cyclic voltammetry, and open-circuit voltage measurement). X-ray diffraction was also used to investigate the structural changes for both types of compounds at different oxidation depths at first charge. The results show that a two-phase reaction (cubic a(0) = 8.154 Angstrom and a(0) = 8.072 Angstrom) occurred in the range of 0.1 < x < 0.45, and a one-phase reaction [cubic a(0) = 8.163 to 8.247 Angstrom] occurred in the range of 0.45 < x < 1.0 for the first charge for the type I spinel. A one-phase reaction (cubic a(0) = 8.105 to 8.223 Angstrom) was observed over the entire intercalated range of 0.25 < x < 1.04 for the type II spinel compound. The capacity fading on cycling for the type I spinel occurs only in the range of 0.1 < x < 0.45, where the shape of the charge and discharge curves in this range was gradually changed to an S-shape from and L-shape during cycling. This is attributed to the fact that the two-phase structure is transformed to more stable one-phase structure.

Dependence of Battery Performance of Spinel Li{sub 1+x}mn{sub 2}o{sub 4} on the Preparation Method

Dependence of Battery Performance of Spinel Li1+XMn2O4 on the Preparation Method

Optimization of Spinel Li[sub 1+x]Mn[sub 2−y]O[sub 4] as a 4 V Li-Cell Cathode in Terms of a Li-Mn-O Phase Diagram

An Investigation of Lithium Ion Insertion into Spinel Structure Li-Mn-O Compounds

Optimization Of Spinel Li1+Xmn2-Yo4 As A 4 V Li-Cell Cathode In Terms Of A Li-Mn-O Phase Diagram

Studies on an LiMnO Spinel System (obtained by Melt-Impregnation) As a Cathode for 4 V Lithium Batteries Part 1. Synthesis and Electrochemical Behaviour of LixMn2O4

Studies on LiMnO spinel system (obtained from melt-impregnation method) as a cathode for 4 V lithium batteries Part II. Optimum spinel from γ-MnOOH

Preparation of Submicrocrystal LiMn2O4 Used Mn3O4 As Precursor and Its Electrochemical Performance for Lithium Ion Battery

Studies of Spinal Li 1+x Mn 2-X O 4 Rechargeable Lithium Ion Battery

Synthesis And Electrochemical Performance Of Linixmn2-Xo4 Spinel As Cathode Material For Lithium Ion Batteries

Differences in Electrochemical Behavior of LiMn2O4 and Li1+xMn2O4 As 4-V Li-cell Cathodes

Spinel Li1 + Xmn2o4 Synthesized by Coprecipitation As Cathodes for Lithium-Ion Batteries

Studies on the LiMnO spinel system (obtained from melt-impregnation method) as positive electrodes for 4 V lithium batteries. Part III. Characterization of capacity and rechargeability

Lithium Manganese Spinel Cathodes for Lithium‐Ion Batteries

Preparation of Spinel LiMn2O4 from Manganese Oxide and Its Electrochemical Performance

Boosting the Electrochemical Performance of a Spinel Cathode with the In Situ Transformed Allogenic Li-Rich Layered Phase

Performance Improvement of Li-rich Layer-Structured Li1.2Mn0.54Ni0.13Co0.13O2 by Integration with Spinel LiNi0.5Mn1.5O4

Dependence of electrochemical properties of spinel LiMn2O4 on Li2CO3 with micro-flaky, micro-flower and nanorod morphologies

Preparation of Cathode Materials for Lithium Batteries by Melt Impregnation Method .1. Preparation of Spinel Limn2o(4)

Synthesis and Electrochemical Performance of LiNi0.5Mn1.5O4 Spinel Compound

Studies on Li-Mn-O Spinel System (obtained from Melt-Impregnation Method) As a Cathode for 4 V Lithium Batteries Part IV. High and Low Temperature Performance of LiMn2O4