Abstract:Two kinds of spinel structure lithium manganese oxides obtained by a melt-impregnation method were examined in a lithium nonaqueous cell. The first type shows a voltage profile of a typical spinel electrode with the characteristic two-step process, which delivers a larger capacity, but fading capacity on cycling (type I). The other type delivers a slightly lower capacity and has ideal rechargeability with a quasi-one-step process (type II). The mechanism of the lithium ion insertion into the spinel compound was studied by several physical and chemical methods (differential chronopotentiometric curves, cyclic voltammetry, and open-circuit voltage measurement). X-ray diffraction was also used to investigate the structural changes for both types of compounds at different oxidation depths at first charge. The results show that a two-phase reaction (cubic a(0) = 8.154 Angstrom and a(0) = 8.072 Angstrom) occurred in the range of 0.1 < x < 0.45, and a one-phase reaction [cubic a(0) = 8.163 to 8.247 Angstrom] occurred in the range of 0.45 < x < 1.0 for the first charge for the type I spinel. A one-phase reaction (cubic a(0) = 8.105 to 8.223 Angstrom) was observed over the entire intercalated range of 0.25 < x < 1.04 for the type II spinel compound. The capacity fading on cycling for the type I spinel occurs only in the range of 0.1 < x < 0.45, where the shape of the charge and discharge curves in this range was gradually changed to an S-shape from and L-shape during cycling. This is attributed to the fact that the two-phase structure is transformed to more stable one-phase structure.

Studies on the LiMnO spinel system (obtained from melt-impregnation method) as positive electrodes for 4 V lithium batteries. Part III. Characterization of capacity and rechargeability

Studies on an LiMnO Spinel System (obtained by Melt-Impregnation) As a Cathode for 4 V Lithium Batteries Part 1. Synthesis and Electrochemical Behaviour of LixMn2O4

Studies on LiMnO spinel system (obtained from melt-impregnation method) as a cathode for 4 V lithium batteries Part II. Optimum spinel from γ-MnOOH

Dependence of Battery Performance of Spinel Li{sub 1+x}mn{sub 2}o{sub 4} on the Preparation Method

Studies of Spinal Li 1+x Mn 2-X O 4 Rechargeable Lithium Ion Battery

Optimization of Spinel Li[sub 1+x]Mn[sub 2−y]O[sub 4] as a 4 V Li-Cell Cathode in Terms of a Li-Mn-O Phase Diagram

Optimization Of Spinel Li1+Xmn2-Yo4 As A 4 V Li-Cell Cathode In Terms Of A Li-Mn-O Phase Diagram

Dependence of Battery Performance of Spinel Li1+XMn2O4 on the Preparation Method

Preparation of Submicrocrystal LiMn2O4 Used Mn3O4 As Precursor and Its Electrochemical Performance for Lithium Ion Battery

Changes in Mn3+/Mn4+ Ratio, Resistance Values in Electrochemical Impedance Spectra, and Rate Capability with Increased Lithium Content in Spinel LixMn2O4

Preparation of Cathode Materials for Lithium Batteries by Melt Impregnation Method .1. Preparation of Spinel Limn2o(4)

Studies on Li-Mn-O Spinel System (obtained from Melt-Impregnation Method) As a Cathode for 4 V Lithium Batteries Part IV. High and Low Temperature Performance of LiMn2O4

IR Investigation and Electrochemical Properties of Li-doped Spinel Li 1 + x Mn 2 – x O 4 Prepared by a Simplified Technique

An Investigation of Lithium Ion Insertion into Spinel Structure Li-Mn-O Compounds

Effect of Lithium Content on the Electrochemical Properties of Solid-State-synthesized Spinel LixMn2O4

Studies on synthesis of cathode material LiMn2O4 for lithium-ion batteries and it's electrochemical performance

Synthesis And Electrochemical Performance Of Linixmn2-Xo4 Spinel As Cathode Material For Lithium Ion Batteries

Studies on Synthesis of Cathode Material LiMn2O4 for Lithium-Ion Batteries and It's Electrochemical

Structure and electrochemical properties of LiMgxMn2-xO4 cathode materials for Li-ion batteries

Preparation and Electrochemical Properties of X Li2MnO3·(1-x)LiMn2O4 Composites

Investigation of Lithium Ion Kinetics Through Limn2o4 Electrode in Aqueous Li2so4 Electrolyte