Abstract:A wind turbine is a conversion mechanism that converts wind energy into electrical energy, but the conversion efficiency cannot reach 100%, so there is partial loss. These losses are converted into thermal energy, which in turn causes the wind turbine to heat up and affect generator performance. Therefore, the cooling and temperature field analysis of wind turbines is very important. In this paper, an electromagnetic analysis model is established by using the parameters of a 4 MW wind turbine; the losses of each part of the generator under rated load and three-phase short-circuit conditions are calculated, respectively; and the heat source is imported into the workbench fluent software to determine the cooling mode, so as to obtain the magnetic-thermal-flow field coupling model of permanent magnet synchronous direct drive wind turbine. The temperature distribution and temperature rise of the generator are obtained. Under the rated load condition, the overall maximum temperature rise of the wind turbine is 41.4 °C, about 180 mm near the fluid outlet side, which is as high as the winding temperature rises, because the winding is the main heating body. The maximum temperature rise of the rotor model and the permanent magnet model is about 36 °C. Under the three-phase short circuit condition, the temperature distribution of each component is similar to that under the rated load condition, and the temperature near the fluid inlet is low; the lowest is only 29.8 °C. The higher the temperature at the fluid's outlet, but not close to it, the higher the temperature is when it is about 180 mm away from the fluid's outlet side. The temperature difference in the same axial length is relatively large, with a maximum temperature difference of about 120 °C. The temperature distribution and temperature rise of the generator are independent of the operating conditions, which mainly affect the value. Additionally, through experimental verification, the minimum error under the rated load condition is 1.05%, the maximum error is 3.3%, and the average error is 2.30%. The minimum error under the three-phase short-circuit condition is 1.5%, the maximum error is 3.62%, and the average error is 2.26%. The difference with the engineering error range requirements is small, indicating the reasonable and effective effectiveness of this method. This study aims to provide a strong reference for analyzing the cooling and magnetic thermal flow field and a coupling analysis of direct drive wind turbines.

Ventilation and Stator Temperature Field of Bulb Tubular Turbine Generator

The Numerical Analysis Of Ventilation And Temperature Fields For A Bulb Tubular Turbine Generator

Optimal Analysis on Temperature Field of Stator Ventilation System Based on Longitudinal Vortex Generator

Enhanced Ventilation and Thermal Performance by Skewed Through Holes on Rotor Yoke in Forced Air-Cooled Permanent Magnet Wind Generators

Heat transfer coefficient distribution in inner surface of stator ventilation duct for large capacity air-cooled turbine generator

Simulation Study on Closed-circuit Ventilation System of Large Vertical Hydraulic Turbine Generator

Analysis of Magnetic-Thermal Coupled Fields in the End Region of Large Turbine-Generators

Design of the external forced air cooling control strategy for the bulb tubular turbine generator based on multi-objective optimization

Stator Non-Uniform Radial Ventilation Design Methodology for a 15 MW Turbo-Synchronous Generator Based on Single Ventilation Duct Subsystem

Thermal Analysis of a Permanent Magnet Generator with Built-in Hydrostatic Drive

Coupled field finite element analysis for turbine generator under loss-of-excitation asynchronous operation

Numerical Calculation of Fluid Heat Transfer in Rotor of Large Air-cooled Generator Based on Global Ventilation Network Model

Dynamical characteristics and influencing factors of stator end-windings of a turbine generator analyzed via heterogeneous element fusion modeling

3D finite element study of transient electromagnetic forces acting on the stator end-windings of a large turbo-generator

Influence of Complex Fluid Flow on Temperature Distribution in the Rotor Region of Large Hydrogenerator Under the Rotor Rotation

Research on Temperature Distribution of Large Permanent Magnet Synchronous Direct Drive Wind Turbine

The dynamic performance and temperature distribution of turbine generator under loss of excitation by using coupled FE analysis

Research on the Nonlinear Thermal-liquid Coupled Network Model of Whole Stator of Three-gorge Generator

CFD simulation and investigation on flow field characteristics and temperature predictions of an electric generator unit

Comparing Between 3D Finite-element Method and Thermal-circuit Method of Calculating Thermal-resistances in the Thermal Field of Three-gorge Hydrognerator

Thermal Modeling and Experimental Validation in the Rotor Region of Hydrogenerator With Different Rotor Structures