Abstract:A wind turbine is a conversion mechanism that converts wind energy into electrical energy, but the conversion efficiency cannot reach 100%, so there is partial loss. These losses are converted into thermal energy, which in turn causes the wind turbine to heat up and affect generator performance. Therefore, the cooling and temperature field analysis of wind turbines is very important. In this paper, an electromagnetic analysis model is established by using the parameters of a 4 MW wind turbine; the losses of each part of the generator under rated load and three-phase short-circuit conditions are calculated, respectively; and the heat source is imported into the workbench fluent software to determine the cooling mode, so as to obtain the magnetic-thermal-flow field coupling model of permanent magnet synchronous direct drive wind turbine. The temperature distribution and temperature rise of the generator are obtained. Under the rated load condition, the overall maximum temperature rise of the wind turbine is 41.4 °C, about 180 mm near the fluid outlet side, which is as high as the winding temperature rises, because the winding is the main heating body. The maximum temperature rise of the rotor model and the permanent magnet model is about 36 °C. Under the three-phase short circuit condition, the temperature distribution of each component is similar to that under the rated load condition, and the temperature near the fluid inlet is low; the lowest is only 29.8 °C. The higher the temperature at the fluid's outlet, but not close to it, the higher the temperature is when it is about 180 mm away from the fluid's outlet side. The temperature difference in the same axial length is relatively large, with a maximum temperature difference of about 120 °C. The temperature distribution and temperature rise of the generator are independent of the operating conditions, which mainly affect the value. Additionally, through experimental verification, the minimum error under the rated load condition is 1.05%, the maximum error is 3.3%, and the average error is 2.30%. The minimum error under the three-phase short-circuit condition is 1.5%, the maximum error is 3.62%, and the average error is 2.26%. The difference with the engineering error range requirements is small, indicating the reasonable and effective effectiveness of this method. This study aims to provide a strong reference for analyzing the cooling and magnetic thermal flow field and a coupling analysis of direct drive wind turbines.

The dynamic performance and temperature distribution of turbine generator under loss of excitation by using coupled FE analysis

Coupled field finite element analysis for turbine generator under loss-of-excitation asynchronous operation

Analysis of Dynamic Processes for Turbo-Generator

Analysis of Magnetic-Thermal Coupled Fields in the End Region of Large Turbine-Generators

Loss Investigation for Multiphase Induction Machine under Open-Circuit Fault Using Field–Circuit Coupling Finite Element Method

A De-excitation Simulation of No-load Hydro-turbine Generator with Damping Winding

Dynamic performance for turbo generator under low excitation and loss of field

Coupling analysis of high speed PM generator used for distributed generation system

Computation of transient electromagnetic torque in a turbogenerator under the cases of different sudden short circuits

Loss Calculation and Thermal Simulation Analysis of High-Speed PM Synchronous Generators with Rotor Topology

Research on Temperature Distribution of Large Permanent Magnet Synchronous Direct Drive Wind Turbine

De-Excitation Simulation of 1 000 MW Steam-turbine Generator after Abrupt Three-phase Short Circuit

3-D Eddy Current Analysis in the End Region of a Turbogenerator by Using Reduced Magnetic Vector Potential

3D finite element study of transient electromagnetic forces acting on the stator end-windings of a large turbo-generator

Transient Process Analysis of Multi-Physical Parameters of Turbine Generator During Out of Phase Synchronization Fault

Loss Estimation of Brushless Doubly-Fed Generator with Hybrid Rotor Considering Multiple Influence Factors

Modeling Principle and Parameter Identification of Double Fed Wind Turbine for Electromechanical Transient Simulation of Power System

Thermoanalysis of the Permanent Magnet Rotor of the Microturbine Generator

Ac Loss Analysis on an Hts Field Winding of the Generator with T-A Formulation

Permanent magnet generator 3D transient temperature field analysis based on magnetic-thermal element coupling algorithm

Numerical Study on Transient Behaviours of a 30-kW Generator Using a Coupling Method