Abstract:Studying the dynamic aerodynamic characteristics and flow field characteristics for the dynamic mode transition in the variable cycle compression system (VCCS) can guarantee that the variable cycle engine (VCE) achieves high performance and stable mode transition. The common quasi-steady state analysis method cannot reflect the transient performance of the dynamic mode transition. Moreover, the dynamic simulation based on the dynamic grid technology will encounter the problem of negative volume grids because the adjustment range of variable components for VCCS is usually very large. To solve the problem, a dynamic simulation method based on real-time variation for geometry and aerodynamic boundaries of the dynamic mode transition in VCCS is first established in this paper. Using this method, the dynamic simulation was completed for the couple adjustment process of the outer bypass valve and variable stators of the dynamic mode transition in VCCS. The results of the dynamic simulation are compared with the quasi-steady state results. The results show that the rotor work ability and stator separation degree are affected by the stator variable angle degree and the mass flow rate (MFR) during the dynamic opening process of the outer bypass valve. For the MFR variation of 14.8%, when the stator variable angle is small (less than 3.3° in this study example), the flow separation on the variable stator blade pressure surface is increased during the dynamic opening process of the outer bypass valve. And the work ability of the downstream rotor is weakened. Therefore, in order to reduce the flow separation of stator blades with a small variable angle during the dynamic opening process of the outer bypass valve, a larger positive incidence angle can be adopted for stators at a small bypass ratio. For the whole dynamic process, the variation trend of the rotor work ability and stator separation state is opposite in the opening and closing process of the outer bypass valve. However, there is a dynamic effect of the flow field variation lagging behind the geometry variation in the opening and closing process. Therefore, the transient flow field in the opening and closing process is different from the quasi-steady state results, and the difference is more significant in the case of a small valve opening. Under a small valve opening, the work ability of the stage before the outer bypass entrance in the open process is significantly smaller than that in the closing process. And the difference in the flow field is mainly that the stator separation state of the stage before the outer bypass entrance in the open process is significantly weaker than that in the closing process. Therefore, the dynamic effect of the opening and closing process is more significant under a small valve opening, and the flow stability problem is more likely to occur during the dynamic mode transition in VCCS.

Simulation Study on Closed-circuit Ventilation System of Large Vertical Hydraulic Turbine Generator

Ventilation and Stator Temperature Field of Bulb Tubular Turbine Generator

Optimal Analysis on Temperature Field of Stator Ventilation System Based on Longitudinal Vortex Generator

The Numerical Analysis Of Ventilation And Temperature Fields For A Bulb Tubular Turbine Generator

Numerical Calculation of Fluid Heat Transfer in Rotor of Large Air-cooled Generator Based on Global Ventilation Network Model

Heat transfer coefficient distribution in inner surface of stator ventilation duct for large capacity air-cooled turbine generator

Stator Non-Uniform Radial Ventilation Design Methodology for a 15 MW Turbo-Synchronous Generator Based on Single Ventilation Duct Subsystem

Influence of Complex Fluid Flow on Temperature Distribution in the Rotor Region of Large Hydrogenerator Under the Rotor Rotation

Full 3D eddy current and temperature field analysis of large hydro-generators in different operating conditions

Design of the external forced air cooling control strategy for the bulb tubular turbine generator based on multi-objective optimization

Improving Combined Flow and Thermal Network Accuracy for Radially Air-Cooled Generators by Considering the Nonlinear Resistance Characteristics of T-Junction Flow

Predicting Airflow Distribution in A Radially Air-Cooled Generator by Flow Network Method

3D Eddy Current and Temperature Field Analysis of Large Hydro-Generators in Leading Phase Operations

Dynamic Numerical Simulation Method and Flow Characteristic Analysis on the Mode Transition in Variable Cycle Compression System

3D finite element study of transient electromagnetic forces acting on the stator end-windings of a large turbo-generator

Thermal Modeling and Experimental Validation in the Rotor Region of Hydrogenerator With Different Rotor Structures

Study on ventilation effect for a large space in an underground hydropower station

Numerical Simulation and Analysis on Hydraulic Performance in Vertical Canned Motor Pump

A Comparative Study on Coupled Fluid–Thermal Field of a Large Nuclear Turbine Generator with Radial and Composited Radial–Axial–Radial Ventilation Systems

Study on Simulation and Measurement of Hydropower Plant Ventilation System

CFD simulation and investigation on flow field characteristics and temperature predictions of an electric generator unit