Abstract:A new magnetic IIP was synthesized to develop an environmentally benign SPE coupled FAAS method for preconcentration, trace determination and removal of the persistent, bio‐accumulative, toxic contaminant of emerging concern; Ni(II). The method was optimized using RSM‐CCD and ANN. Apart from regeneration Ni(II) loaded IIP was exploited for reduction of permanganate ions, further reducing pollution. In order to study transportation and biomagnification of Ni(II) trace‐determination, and removal of Ni(II) was performed in ground water, wastewater, and food samples. A novel silica fabricated allyloxy ethanol based imprinted polymer is synthesised with surface area of 333 m2 g−1 and average pore size of 6.5 nm by an environment friendly one pot surface imprinting process. It was employed for the selective solid‐phase extraction (SPE) of trace Ni(II) in real samples prior to FAAS determination. The factor settings produced via central composite design in response surface methodology (RSM) (pH: 3.6; initial concentration; 800 mg L−1 and time; 15 minute) provide adsorption capacity of 176 mg g−1. Artificial neural network model employed on the RSM data, provided better predictability. Sips isotherm model and BSf kinetic model describes best the sorption phenomena of the homogenous binding terrain. The developed SPE‐coupled FAAS method demonstrate a detection limit of 1.62 μg L−1, quantification limit of 4.17 μg L−1, and Linear dynamic range of 20–8000 μg L−1. It was successfully applied to determine nickel in food (Spinach, Radish, Green tea infusion, Black tea infusion, Coffee, Soya milk, Chocolate Soya milk, Tobacco) and wastewater samples (>99 % removal). For five replicate determinations, the method's relative standard deviation was 2.3 %. The method was validated by analysing two certified reference materials, and the outcomes were well‐congruent with standard values. For the synthesised polymer Ni(II) exhibits higher distribution ratio than other competing ions (Cu(II), Pb(II), Cd(II), and Zn(II)) with the imprinting factor; β values of 5.73, 4.98, 6.80, and 5.04 respectively. The reusability experiments revealed that APS@Ni‐IIP retains a strong adsorption efficacy even after 15 cycles and after its exhaustion it was employed as catalyst for reducing permanganate ions, further reducing pollution. The rigid structure of mesoporous silica contributes to its acid resilience and reusability, which can lead to a relative increase in polymer performance in absorption rate and selectivity. Apart from the novelty in the synthesis, thorough examination of the method and material selectivity (in binary, ternary and multielement system), multi fold applications of determination, removal of Ni(II) and reduction of permanganate ions, makes APS@Ni‐IIP a promising candidate for environmental remediation.

Determination of Nickel after Online Sorbent Preconcentration by FI-FAAS Using Dimethylglyoxime as a Complexing Agent

Determination of trace copper and nickel in environmental and biological samples by flow injection on-line microcolumn preconcentration flame AAS using acrylic acid-grafted polytetrafluoroethylene fiber for column packing

Cobalt determination by means of flow injection on-line sorbent preconcentration-flame atomic absorption spectrometry with 1-nitroso-2-naphthol as a complexing reagent

Iron Determination after On-Line Sorbent Preconcentration by Fi-Fass Using 1, 10-Phenanthroline As a Complexing Agent

Determination of trace cobalt, nickel and cadmium by on-line flow injection analysis with coprecipitation preconcentration FAAS

Determination of Iron( II ) and Total Iron Using Flow Injection On-line Preconcentration with FAAS

Use of a new magnetic ion–imprinted nanocomposite adsorbent for selective and rapid preconcentration and determination of trace nickel by flame atomic absorption spectrometry

Determination of Ni, Cu and Hg by flow injection preconcentration coupled with HPLC

Determination of cadmium in biological materials by flame atomic absorption spectrometry with flow-injection on-line sorption preconcentration

Systematic Study for Determining As, Pb, Cd, and Se in Steel and Nickel Alloy Samples by GF AAS: Circumventing Matrix Interference with Extraction Based on Micellar Separation

Use of Nb(2)O(5)-SiO(2) in an automated on-line preconcentration system for determination of copper and cadmium by FAAS

Determination of lead in nickel nitrate by flow injection with an atomic absorption spectrophotometer

Simultaneous determination of trace amounts of nickel, copper and mercury by liquid chromatography coupled with flow-injection on-line derivatization and preconcentration

Flow-Injection Online Sorbent Extraction Preconcentration for Graphite-Furnace Atomic-Absorption Spectrometry

Determination of Pb and Cd in water sample by on-line ion-exchange preconcentration-FAAS

On-line separation and preconcentration of trace cadmium in environmental water samples by micro column filled with modified nanometer Si-HAP prior to FAAS determination

1,10-Phenanthroline As a Complexing Agent for On-Line Sorbent Extraction/preconcentration for Flow Injection–flame Atomic Absorption Spectrometry

Determination of Silver in Metal Plating Wastewater by Slotted Quartz Tube Flame Atomic Absorption Spectrometry (SQT-FAAS) after Preconcentration with Stearic Acid-Coated Magnetite Nanoparticle-Based Solid-Phase Microextraction (SA-MNP-SPME)

Silica Grafted Imprinted Mesoporous Polymer for the Development of SPE Coupled FAAS Method of Nickel Determination, Removal, and Spent Polymer for Reduction of Permanganate: Multivariate Optimization

Acrylic acid grafted polytetrafluoroethylene fiber as new packing for flow injection on-line microcolumn preconcentration coupled with flame atomic absorption spectrometry for determination of lead and cadmium in environmental and biological samples

Determination of Ni,Al,P,Mg and Ca in Nickel Ores by Inductively Coupled Plasma-Atomic Emission Spectrometry