Abstract:Due to native deficiency of the interfacial mismatch between Al2O3 and Al-melt, as well as micron-Al2O3 segregation at matrix grain boundaries (GBs), achieving both high strength and fracture toughness has been the long-lasting challenge for Al-CuO composite fabricated by conventional casting. Herein, we report a novel manufacturing of Al-CuO composite via shift-speed ball-milling (SSBM) of Al-5 wt.% CuO powders and afterwards subjected to hot-pressing (HP) as well as heat treatment. Comprehensive characterization shows that in-situ generation of the two types of Al2O3 with intragranular distribution, including δ*-Al2O3 particles (∼200 nm) and γ-Al2O3 whiskers (length of ∼150 nm, thickness of ∼20 nm), was governed by a diffusion-assisted nucleation-regime ascribing to the intense thermal effect of Al-CuO reaction. The size and spatial distribution of Al2O3 were emphasized to address their contribution to the high mechanical performance of the composite, which exhibits a tensile strength of ∼481 MPa and fracture elongation of ∼16.8 %. Meanwhile, the toughening mechanism of present Al-CuO composite was rationalized on basis of the "dislocation punched zone" and "plastic zone" affected by Al2O3. Both the theoretical analysis and fracture morphology support a reinforcements-matrix interface failure mechanism and the non-uniform distribution of Al2O3 consisting alternant "rich/poor zones" can markedly contribute to the high toughness. The present findings may provide a promising strategy to achieve an intragranular distribution of nano-sized reinforcements in Al-metal oxides composites, which enables increasing strength and ductility of the metal matrix.

Nanostructured Composite Obtained by Mechanically Driven Reduction Reaction of Cuo and Al Powder Mixture

Reduction reaction in Al-CuO powder mixture driven by mechanical alloying

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Preparation of Ti/Al based nanophase composite powder by mechanical alloying

Preparation of ti-al based nanophase composite powder by mechanical alloying

Nano-sized amorphous alumina particles obtained by ball milling ZnO and Al powder mixture

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

Nanoparticle Reinforced Metal Composites Prepared by Electrocodeposition

PREPARATION OF Cu MATRIX COMPOSITE REINFORCED WITH IN-SITU NANOSIZED Al2O3 PARTICLE POWDER FROM METAL NITRATES

Revealing the strengthening and toughening mechanisms of Al-CuO composite fabricated via in-situ solid-state reaction

Mechanical Activation-Assisted Solid-State Aluminothermic Reduction of CuO Powders for In-Situ Copper Matrix Composite Fabrication

Sintering Densification of Cu/Al2O3p Nano-Composite Powders by Electroless Copper Plating

Structure and Properties of Electrocodeposited Cu-Al2o3 Nanocomposite Thin Films

Towards Homogeneous Distribution of Coarse Grain in a Tri-Modal Al-based Composites Utilizing Localized Grain Growth

Study of Hot-press Sintering Process of Nanometer Cu-Al_2O_3 Composite

Enhanced Combination of Strength and Ductility in Ultrafine-Grained Aluminum Composites Reinforced with High Content Intragranular Nanoparticles

Preparation of in situ TiC@TiN core–shell and Ti2N–Al4C3 nanoparticles and their effects on Al–Zn–Mg–Cu alloy

Performance of a Hierarchically Nanostructured W–Cu Composite Produced via Mediating Phase Separation

Dual-nanoparticulate-reinforced aluminum matrix composite materials

A comprehensive study of Al-Cu-Mg system reinforced with nano-ZrO2 particles synthesized by powder metallurgy technique

Effect of nano-Al2O3 addition on microstructure and mechanical properties of Ti2AlNb-based composites prepared by powder metallurgy