Abstract:Using Mo, Si, and C element powders as starting materials, a field-activated and pressure-assisted combustion synthesis (FAPACS) was employed to synthesize high-density bulk MoSi2–SiC composite in one step. Effects of sintering temperatures (1100, 1200, 1400 and 1600°C) on microstructures and densification were investigated. With the exception of 1100°C, at which synthesis was incomplete, the FAPACS was characterized by the four stages, i.e. initial expansion, slight shrinkage, abrupt shrinkage and slight expansion. The study shows that the sintering ability at the higher temperature is better than that at the relatively lower temperature. When the sintering temperature reaches 1400 or 1600°C with holding time of 10min, the high-temperature transitional phases, i.e. Mo4.8Si3C0.6, were presented and the produced SiC particles are agglomerate. The relative density of the products (holding time: 10min) was improved tremendously from 59% to 96.0% over the range 1100–1400°C, and a smaller enhancement in densification up to 98.5% was achieved between 1400 and 1600°C. Moreover, an extended holding time (up to 20min) at 1600°C resulted in nearly Mo4.8Si3C0.6-free and dense MoSi2–SiC products with the relative density of 99.0%. Simultaneously, a locally uniform distribution of SiC in the synthesized MoSi2 matrix was achieved. And the interfaces between the synthesized phases are clean without impurities (e.g. SiO2) and porosities. Thereby, in order to pursue an equilibrium among densification, microstructural uniformity and formation of transitional phases, the most suitable sintering temperature and holding time for fabrication of MoSi2–SiC by FAPACS are recommended to be 1600°C and 20min in the present work.

Synthesis of SiC/MoSi2 composite by mechanical alloying and reactive sintering

The study of pressureless-sintered Mo(Si,Al)(2)-SiC composite

Processing and Mechanical Properties of Multiphase Composites Based on Mo–Si–Al–C System

Preparation of Intermetallic Compound MoSi2 by Mechanical Alloying Method

Microstructural Characterization of Sintered MoSi<sub>2</sub>/SiC<sub>P</sub> Composites

Microstructural characterization of sintered MoSi2/SiCp composites

The Microstructure and Mechanical Property of Mo(Si, Al)2-SiC Composite Prepared by Infiltrating Melt Aluminum

Preparation of A MoSi2-SiCp composite by reactive sintering without pressure

In-situ Preparation of Nano MoSi 2 SiC Composite by Melt Infiltration of Silicon Method

Mo-Si Compound Composites Synthesized by in Situ Reaction

Synthesis of Ti3SiC2 Powder by Mechanical Alloying and Mechanical Property of the Sintered Compacts.

Synthesis Nano-Sicp/Mosi2 Composites by In-Situ Reaction Sintering and Low Temperature Oxidation Behavior

MoSi_2/SiC COMPOSITE PREPARED BY USING REACTION - MELTING INFILTRATION SINTERING

Synthesis and properties of MoAlB composites reinforced with SiC particles

Synthesis of Mosi2 by Mechanical Alloying

Synthesis and analysis of high-purity MoSi2 powder

Synthesis of Mo(Si, Al)2 Powders by Mechanical Alloying

Microstructure and mechanical properties of in situ SiC particulates reinforced MoSi2 matrix composite

Phase composition and mechanical properties of in-situ synthetic Mo-Si compound composites

Microstructures and densification of MoSi2–SiC composite by field-activated and pressure-assisted combustion synthesis

Rare earth monosilicates as oxidation resistant interphase for SiCf/SiC CMC: Investigation of SiCf/Yb2SiO5 model composites