Abstract:After the converter steelmaking process, a considerable number of ferroalloys are needed to remove dissolved oxygen from the molten steel, but it also forms a lot of oxide inclusions that cannot be completely removed. At the same time, it increases the carbon emissions in the steel production process. After years of research, our team have developed a series of clean deoxidation technologies, including carbon deoxidation, hydrogen deoxidation, and waste plastic deoxidation of molten steel to address the aforementioned issues. In this study, thermodynamic calculations and laboratory experiments were employed to verify that carbon and hydrogen can reduce the total oxygen content in the molten steel melt to below 5 × 10 −6 and 10 × 10 −6 , respectively. An analysis of the deoxidation mechanisms and effects of polyethylene and polypropylene was also conducted. In addition, the applications of carbon deoxidation technology in different steels with the hot-state experiment and industrial production were discussed carefully. The carbon deoxidation experimental results of different steels were as follows: (1) the oxygen content of bearing steel was effectively controlled at 6.3 × 10 −6 and the inclusion number density was lowered by 74.73% compared to aluminum deoxidized bearing steel; (2) the oxygen content in gear steel was reduced to 7.7 × 10 −6 and a 54.49% reduction of inclusion number density was achieved with almost no inclusions larger than 5 μm from the average level of industry gear steels; (3) a total oxygen content of M2 high-speed steel was as low as 3.7 × 10 −6 . In industrial production practice, carbon deoxidation technique was applied in the final deoxidation stage for non-aluminum deoxidized bearing steel, and it yielded excellent results that the oxygen content was reduced to below 8 × 10 −6 and the oxide inclusions in the steel mainly consist of silicates, along with small amounts of spinel and calcium aluminate.

Study on Low Carbon Steel Deoxidized by Magnesium Alloy

Evaluating the Effect of MgO/Al2O3 Ratio on Thermal Behaviors and Structures of Blast Furnace Slag with Low Carbon Consumption

Deoxidation of Molten Steel with CaO-Al_2O_3 Based Refining Slag

Effect of Silicon–Manganese Deoxidation on Oxygen Content and Inclusions in Molten Steel

Reduction of CaO and MgO Slag Components by Al in Liquid Fe

Development and prospects of molten steel deoxidation in steelmaking process

New steelmaking process based on clean deoxidation technology

Effects of CaO Content and Magnesium Additive in Electroslag on Desulfurization of Rejected Electrolytic Manganese Metal Scrap

Magnesia–carbon refractory dissolution in Al killed low carbon steel

Effect of Al on the Cleanliness of the x% Al–7CrSiMnMoV Steel Produced by Scrap Steel

An Innovative CaO–SiO2–MgO-Refining Slag Containing 12 to 16 Mass Pct MgO for Tire Cord Steel

Dissolution Behavior of Mg from Magnesia-Chromite Refractory into Al-killed Molten Steel

Dissolution Behavior of Mg and Ca from Dolomite Refractory into Al-killed Molten Steel

Dissolution behavior of spent MgO–C refractory in the CaO–SiO2–FeO slag system as a steelmaking flux

Optimum Composition of Cao-Sio2-Al2o3-Mgo Slag for Spring Steel Deoxidized by Si and Mn in Production

Study on magnesium reduction process for air-cooled high magnesium-bearing blast furnace slag

Effect of Rare Earth–Magnesium Alloy on Inclusion Evolution in Industrial Production of Die Steel

Study on the Melting Temperature of CaF2-CaO-MgO-Al2O3-TiO2 Slag under the Condition of a Fixed Ratio of Titanium and Aluminum in the Steel during the Electroslag Remelting Process

Research of Si-Ca-Ba Compound Deoxidizer Composition Optimization for Steelmaking

Designing low-carbon MgO–Al2O3–La2O3–C refractories with balanced performance for ladle furnaces

Reaction Mechanism between MgO and MgOC Lining Refractories and a High‐Carbon Al‐Killed Steel