Abstract:In this study, the effects of Si content on the glass-forming ability (GFA), thermal stability, annealing window, nanocrystallization process, and soft magnetic properties (SMPs) of Fe 86.3-x Si x B 10 P 2 Cu 1.7 (x = 0, 1, 2, 3, and 4, denoted as Si0, Si1, Si2, Si3, and Si4, respectively) alloys with high Fe and Cu contents were investigated. Moderate addition of Si (x = 1, 2, and 3) enhanced the GFA and suppressed the precipitation of compound phases, thus leading to a large crystallization temperature interval ( ΔT x ) exceeding 185 °C for the alloys. Appropriate addition of Si also resulted in the formation of high-density and fine pre-existing α-Fe nanocrystals in as-spun ribbons and a high growth active energy of α-Fe crystals during the subsequent nanocrystallization process for the Si1, Si2, and Si3 alloys, enhancing competitive growth between α-Fe crystals and resulting in fine nanostructure and excellent SMPs of the nanocrystalline alloys (NAs). As a result, the Si1, Si2, and Si3 NAs obtained by annealing at 420 °C for 30 min exhibited excellent SMPs with saturation magnetic flux density ( B s ) up to 1.84 T and a low coercivity ( H c ) of approximately 10 A/m. In addition, statistical analysis of the relationship between the average grain size ( D ) of α-Fe crystals and H c values of the NAs indicated that an H c α D 3 dependence is observed when the D is less than approximately 30 nm, while this dependence follows the well-known H c α D 6 relationship when the D is above 30 nm. The dependency relationship between D and H c of NAs can guide the selection of an appropriate annealing process to optimize their SMPs.

Formation behavior, microstructure and mechanical properties of multi-cation α-sialons containing calcium and neodymium

Formation of an α-SiAlON Layer on ß-SiAlON and Its Effect on Mechanical Properties

First-principles Calculations of the Stability and Local Structure of -Sialon Ceramics on the Line Si3N4–½Ca3N2:3AlN

Preparation and formation mechanism of elongated (Ca, Dy)-α-sialon powder via carbothermal reduction and nitridation

Preparation And Formation Mechanism Of Elongated (Ca,Dy)-Alpha-Sialon Powder Via Carbothermal Reduction And Nitridation

Microstructural Characteristic of Α'-Aln-polytypoids Multi-phase Sialon

Effects of in situ Mg-Sialon and β-Sialon on the microstructure and properties of MgAl2O4-SiC composites

In situ synthesis of PcBN composites by Sialon combined with cBN-TiB2-AlN and their properties

Phase Composition and Physicomechanical Properties of β-Sialons Prepared Using NaF as a Sintering Aid

Microstructure and Room-Temperature Mechanical Properties of Β Sialon/sic Nanocomposites

The nanomechanical properties of non-crosslinked calcium aluminosilicate hydrate: The influences of tetrahedral Al and curing age

Preparation and mechanical properties of SiC-AlN ceramic alloy

Preparation, structure and mechanical properties of Sialon ceramics by transition metal-catalyzed nitriding reaction

Solid-state NMR Characterization of Β-Sialons from Self-Propagating High-Temperature Synthesis

Microstructure and mechanical properties of SiC reinforced AlSi10Mg composites fabricated by laser metal deposition

Nano-Phase and SiC–Si Spherical Microstructure in SiC/Al-50Si Composites Solidified under High Pressure

Sintering And Mechanical Properties Of Aln-Rich Ceramics In The Sic-Aln System

Influence of Al2O3/SiO2 ratio in multicomponent LNAS glasses and glass-ceramics on the crystallization behavior, microstructure and mechanical performance

Microstructures and Mechanical Properties of As-Cast Mg–5Al–0.4Mn–xNd (x = 0, 1, 2 and 4) Alloys

Effects of Si addition on crystallization process and soft magnetic properties of high-Fe and high-Cu-content Fe-Si-B-P-Cu nanocrystalline alloys

Uniaxial tensile study of calcium aluminosilicate hydrate (C-A-S-H): Structure, dynamics and mechanical properties