Bipolar Axial Magnetic Field Electrode for Vacuum Interrupter

WANG Ji-mei,LIU Zhi-yuan

2005-01-01

Abstract:In this paper, the bipolar axial magnetic field electrode is introduced. The magnetic field has been calculated and evaluate. From the results, it shows that this electrode is suitable for high voltage and high current applications.

What problem does this paper attempt to address?

Analysis of Axial Magnetic Field electrode applied to high voltage Vacuum Interrupters

Xiu Shixin,Pang Lei,Wang Jimei,Lin Jianfei

DOI: https://doi.org/10.1109/DEIV.2006.357295

2006-01-01

Abstract:In order to develop high voltage and large capability vacuum circuit breaker, it is necessary to make sure that there is enough strong axial magnetic field even with long gap distance. In this paper, the magnetic field of those model at the long gap distance were calculated for the coil-type axial magnetic field electrode and the cup-type axial magnetic field electrode, the results show the axial magnetic field distribution on the midplane between the two electrodes, the effect of some electrode structure parameters and the relative position between the two electrodes on the axial magnetic field were studied. Based on the analysis of the results, a new electrode structure applied to high voltage vacuum interrupters was developed
High-interrupting-capability vacuum interrupter with two-pole axial magnetic field electrode

Shenli Jia,Jimei Wang,Jun Fu,Hongqun Li

1997-01-01

Abstract:A kind of vacuum interrupter with two-pole axial magnetic field electrode was developed. 3-D magnetic field distribution was calculated and analyzed. It was found that this kind of vacuum interrupter has lower arc voltage and higher interrupting capability than other kinds.
DEVELOPMENT AND STUDY ON IRON CORE STYLE BIPOLAR AXIAL MAGNETIC FIELD VACUUM INTERRUPTER

Xiu Shixin,Wang Jimei

DOI: https://doi.org/10.1109/isdeiv.2002.1027425

1999-01-01

Abstract:In this paper, a new style of bipolar axial magnetic field electrode structure used in vacuum interrupters is developed and studied, which results in symmetric alternating axial magnetic field distributing intensively and evenly between the electrodes. Thus, no slots on the electrode are needed and the structure strength of the whole electrode is increased. Replacement of solid block iron core by a stromatolithic iron core reduces the eddy current and the lag time of the axial magnetic field behind the arc current. The results of tests show that this electrode structure can reduce the arc voltage and increase the interrupting current capacity of vacuum interrupters.
A New Electrode Applied to High Voltage Vacuum Interrupter and Its Performance

修士新,庞磊,王季梅

DOI: https://doi.org/10.3321/j.issn:0258-8013.2008.24.021

2008-01-01

Abstract:Vacuum interrupter is the core of high voltage vacuum switch. Because of the long contact gap, the axial magnetic field (AMF) contact is widely used to generate stronger and evener AMF in the contacts’ gap. It can reduce arc current density and arc energy, so its interrupting performance is improved. A new AMF electrode applied to high voltage vacuum interrupter was introduced, it has some advantages such as simple structure, easy-machining, strong mechanism intensity and so on. Its axial magnetic field characteristic was calculated and analyzed with the solution of finite element. The calculation results indicated that the axial magnetic field characteristic for the new one is superior to a few traditional electrodes. The vacuum interrupter used the new electrode was tested in the synthetic test circuit, the short-circuit current interrupting ability was still excellent when the contact gap was 40 mm and 60 mm.
Study on a New Single Coil-Type Axial Magnetic Field Contact for High-Voltage Vacuum Interrupters

Shaoying Cheng,Shixin Xiu,Zhiyuan Liu,Jimei Wang

DOI: https://doi.org/10.1109/tps.2007.893264

IF: 1.368

2007-01-01

IEEE Transactions on Plasma Science

Abstract:A new single coil-type axial magnetic field (AMF) contact for high-voltage vacuum interrupters is introduced. Its AMF characteristics were studied by a finite element method, taking the eddy current effect into account. Vacuum arc appearance of the new single coil-type AMF contact was observed by a highspeed charge-coupled device video camera. Capacitors and reactors (LC) discharging current interruption tests up to 45.0 kA were done with a single frequency LC oscillating circuit. Vacuum arc appearance of the single coil-type and slot-type AMF contacts was compared. The research results show that the new single coil-type AMF contact is more suitable for high-voltage vacuum interrupters than the slot-type AMF one.
Analysis of Axial Magnetic Field of an Iron Style Bipolar Axial Magnetic Field Vacuum Interrupter

ZY Liu,JM Wang,Z Wang,SY Gu,GL He

DOI: https://doi.org/10.1109/27.964468

IF: 1.368

2001-01-01

IEEE Transactions on Plasma Science

Abstract:Iron style bipolar axial magnetic field vacuum interrupter is a novel vacuum interrupter and it is the first one that is developed in China. Its axial magnetic field in the gap and eddy current in the iron core are analyzed. It is shown from the static axial magnetic field analysis that its axial magnetic flux density is very high and its distribution is homogeneous on the iron area. The axial magnetic flux density will increase significantly when electrode diameter increases or gap decreases. When the arm width increases the flux density will decrease almost linearly. It is shown that eddy current is related to electrode structure parameters and iron material property. When contact diameter decreases or arm width increases, eddy current will decrease. When gap increases eddy current will decrease slightly. Eddy current will increase nonlinearly with the increase of magnetic permeability and generally does so with the increase of conductivity. It is also shown that a laminated iron core is a good way to reduce eddy current. Since the iron core has an important influence on the AMF, an improved iron core design is obtained
Analysis of static magnetic field of an iron style bipolar axial magnetic field vacuum interrupter by 3D finite element method

Zhi-yuan LIU,Ji-mei WANG,Zheng WANG,Shu-yi GU,Guang-li HE

DOI: https://doi.org/10.3969/j.issn.1003-3076.2001.01.007

2001-01-01

Abstract:The first Chinese vacuum interrupter having intellectual p roperty righ ts is an iron style bipolar axial magnetic field vacuum interrupter and it has hi gh interrupting capability. It is meaningful to analyze its axial magnetic field by numerical method because the results are helpful to make the interrupting ca pability higher. The static axial magnetic field of the vacuum interrupter is an alyzed by finite element method. It is shown that the axial magnetic flux densit y produced by this kind of vacuum interrupter is very high and its distribution is nearly uniform. It is also shown that the axial magnetic field can be influen ced by the structure parameters strongly. The axial magnetic flux density will i ncrease significantly when electrode diameter increases and it will decrease qui ckly when gap increases. When arm width increases the flux density will decrease linearly.
Numerical Analysis on Magnetic Field Characteristic of Axial Magnetic Field Contacts under Long Break Distance

Lei PANG,Shi-xin XIU,Ji-mei WANG,Zhi-yuan LIU

DOI: https://doi.org/10.3321/j.issn:1000-3673.2007.01.012

2007-01-01

Abstract:Several contact structures for medium voltage vacuum interrupters are analyzed and the feasibility of applying them to high voltage vacuum interrupter is researched. Finite element method based simulation and computation of magnetic field characteristics for two kinds of contact structures,i.e.,the coil type of axial magnetic field (AMF) contact structure with one-third turn and cup type of AMF contact structure,under long break distance are conducted.The AMF distribution is optimized by modifying a part of contact structural parameters,and the feasibility of applying them to high voltage vacuum extinction chamber are researched based on results of analytical calculation.Research results show that under the condition of long break distance the magnetic field generated by both above-mentioned contact structures is insufficient to control vacuum arc although a part of contact structural parameters are optimized.The coil type of AMF contact structure with one-half turn possesses more intensive axial magnetic field,so it is suitable to be applied in vacuum interrupters to switch off intense current.
Critical Axial Magnetic Field for Prevention of Anode Spot Formation in Vacuum Interrupters

Guowei Kong,Zhiyuan Liu,Yingsan Geng,Jianhua Wang

DOI: https://doi.org/10.1109/icepe-st.2013.6804304

2013-01-01

Abstract:The objective of this paper is to show an effective critical axial magnetic field (AMF) as a function of contact diameter and arc extinguishing contact gap in vacuum interrupters (VIs), based on prevention of anode spots formation. Experiments were conducted in a demountable vacuum chamber, in which an external Helmholtz AMF coil was installed coaxially between a pair of butt-type contacts. The AMF flux density BAMF applied by the external coil was uniform and it can be adjusted from 0 to 110 mT. The experimental results showed that an effective critical AMF by arc current BAMFeff (mT/kA) needed for prevention of anode spots formation followed a power function with contact diameter D as BAMFeff = sD-α, where s and α were constant and D was in a range of 12~100 mm. And BAMFeff (mT/kA) increased as a linear function with the arc extinguishing contact gap l, even though the increasing of BAMFeff was so slow with l in a range of 12~24 mm. Last, a numerical calculation suggested that anode current density radial distribution contributed to the above findings.
3D Modeling and Simulation of High-Current Vacuum Arc Subjected to Real External Transverse Magnetic Field

Lihua Zhao,Hangyuan Gou,Mengjie Yang,Junwen Ren,Xueyan Bai,Lijun Wang,Xiaolong Huang

DOI: https://doi.org/10.1063/5.0002935

IF: 2.2

2020-01-01

Physics of Plasmas

Abstract:Vacuum circuit breakers (VCBs) are widely used in power distribution systems. When the VCB in a switchgear interrupts the short circuit current, the U type loop, which consists of a vacuum interrupter, an external busbar and a conductive rod, generates an external transverse magnetic field (ETMF). This field deflects the vacuum arc and affects the interruption performance of the VCB. In this paper, the real magnetic field data of the arc region are obtained by establishing a simulation model of an electrode system, taking into account the real ETMF and real axial magnetic field (AMF). Furthermore, the three dimensional steady magnetohydrodynamic model of the vacuum arc is established by using real magnetic field data as the boundary condition. The vacuum arc characteristics under the combined effect of AMF and the asymmetric transverse magnetic field (TMF) are studied. The simulation results show that the ETMF considerably changes the Bx of the arc column, which demonstrates asymmetry in the positive and negative directions, whereas By demonstrates a weaker asymmetry. Moreover, the asymmetric TMF deflects the distributions of the vacuum arc plasma and increases the partial heat flux density and axial current density. With the increase in the severity of the short circuit, the TMF asymmetry of the arc region is enhanced and the deflection of the vacuum arc plasma is also enhanced.
Investigation of DC Vacuum Arc Interruption Ability with Combined Axial and Radial Magnetic Field

Mohmmad Al-Dweikat,Yu Long Huang,Xiaolin Shen,Weidong Liu

DOI: https://doi.org/10.4028/www.scientific.net/amr.516-517.1791

2012-01-01

Advanced Materials Research

Abstract:DC Vacuum Circuit Breakers based arc control has been a major topic in the last few decades. Understanding vacuum arc (VA) gives the ability to improve vacuum circuit breakers capacity. In this paper, the interaction of a DC vacuum arc with a combined Axial-Radial magnetic field was investigated. The proposed system contains an external coil to produce axial magnetic field (AMF) across the vacuum chamber. The vacuum interrupter (VI) contacts were assumed to be untreated radial magnetic field (RMF) contacts. For this purpose, Finite Element Method (FEM) based Multiphysics simulation of the immerging magnetic field influence on the VA is presented. The simulation shown the ability of the presented system to deflect high DC vacuum arc, also reveals that the vacuum arc interruption capability increases with the rise of the axial component of the magnetic field. Simulation results shown that this method can be applied to improve the interruption capability of the VI.
Axial magnetic field strength needed for a 126kV single break vacuum interrupter

Yingyao Zhang,Geng, Yingsan,Yu, Li,Jing Yan

DOI: https://doi.org/10.1109/DEIV.2010.5625829

2010-01-01

Abstract:The objective of this paper is to investigate how strong the axial magnetic field (AMF) is needed for a 126kV vacuum interrupter at different contact gaps. The AMF was generated by a pair of 2/3 coil AMF contacts. First, the accuracy of the three-dimensional finite element simulation of AMF was validated by an AMF measurement at contact gap 30mm. After that high-current switching experiments with the AMF contacts were carried out at different contact gaps of 20mm and 50mm at 40kA rms. Then the AMF at the contact gaps of 20mm and 50mm was simulated to analyze the interrupting experimental results. The results showed that there was a successful interruption at 40kA with an AMF of 235mT at contact gap 20mm. And current interruption failures occurred with an AMF of 146mT at contact gap 50mm.
Calculation ana Analysis of the Electric Field Distribution in High-voltage Interrupter and Its Advance Structure

Zhongyi Wang,Jimei Wang

DOI: https://doi.org/10.3321/j.issn:0258-8013.1998.02.014

1998-01-01

Abstract:Suppose that the potential on the electrodes is asymmetric and the voltage on the floating shield is unknown with the consideration of the influence of the ions on the electrode surface, the electric field distribution in the high-voltage vacuum interrupter is calculated and analyzed with finite-element method, thus the conclusion is drawn that the serious asymmetry of the electric field distribution in the vacuum interrupter has affected the electrical strength and the interrupting performance of the interrupter. Furthermore, the proposal is advanced to make electric field distribute more uniformly or symmetrically.
Arc Behaviours in Vacuum Interrupters with Axial Magnetic Field Electrodes

Wang Zhongyi,Zheng Yuesheng,Liu Zhiyuan,Cheng Shaoyong

DOI: https://doi.org/10.1088/1009-0630/10/5/10

2008-01-01

Abstract:To improve the limiting current interruption capability and minimizing vacuuminterrupter with axial magnetic field（AMF）electrodes,it is significant to investigate the vacuumarc behaviours between the contacts.AMF distributions of the slot type electrodes were studiedby both numerical analysis and experiments.Furthermore,the behaviours of vacuum arcs fordifferent parameters of the slot type AMF electrodes were investigated by using high-speed CCDcamera.The influences of gap distance,contact diameter and phase shift time between AMF andarc current on the vacuum arc were investigated.The results provide a reference for research anddevelopment of vacuum interrupters with slot type or other types of AMF electrode.
Research on Vacuum Arc Characteristics of a New Electrode Structure Applied in High Voltage Vacuum Interrupter

Cheng Shaoyong,Xiu Shixin,Wang Jimei,Shen Zhengchao

DOI: https://doi.org/10.1109/deiv.2006.357263

2006-01-01

Abstract:In this paper the arc modes transition of the AMF electrode with one-turn coil structure is investigated at gap distance 10mm and 40mm respectively. And the axial magnetic field distribution is computed at 10mm and 40mm. High-speed video recording was used as a major diagnostics to investigate the arc behavior. At gap distance 10mm, the vacuum arc maintains diffuse arc mode. With the gap distance increasing from 10mm to 40mm, the vacuum arc experience constricted arc modes only in short time at beginning. In most of time, the vacuum arc keeps in diffuse arc mode. The test results prove that the AMF electrode with one-turn coil structure is feasible to be applied in high voltage interrupter
A Low Resistance Vacuum Interrupter Electrode with Hook Support under Contact Plates

Zeyu Huang,Shenli Jia,Lihua Zhao,Xiaolong Huang,Junping Chen,Haiyang Luo

DOI: https://doi.org/10.23919/isdeiv55268.2023.10199284

2023-01-01

Abstract:Vacuum circuit breakers are extensively utilized in the medium voltage level worldwide, but there are still a series issues in the application for higher voltage levels, among which temperature rise is one of the bottlenecks. This paper introduces a new electrode structure with hooked-type support under contact plates, which is helpful to solve the problem of heat generation. Compared with the traditional support structure, the new type of electrode ensures the current passes through the cup wall of the electrodes to generate a strong enough axial magnetic field (AMF) during the breaking. The hook structure is connected with the contact plates pressed by the contact force in the close state, so that the stable temperature rise is lower. In addition, the special hook structure also has a certain anti-welding strength. The simulation results show that the body resistance of the electrode with hooked-type support structure is different at opening and closing states, and the stable temperature rise of the hooked-type structure is significantly lower than that of the conventional support structure in close state with the rated continuous current. The electrode with hook support has a good anti-welding performance in the event of contact welding.
Critical Radius of Axial Magnetic-Field Contacts in Vacuum Interrupters

Zhiyuan Liu,Zhongyi Wang,Yuesheng Zheng,Jimei Wang

DOI: https://doi.org/10.1109/tpwrd.2008.2002976

IF: 4.825

2009-01-01

IEEE Transactions on Power Delivery

Abstract:Vacuum circuit breakers (VCBs) are widely used to protect medium-voltage (MV) power distribution circuits. Since SF6 gas is specified as a global warming gas, VCBs are stepping into a higher voltage sector to protect power transmission circuits. Axial magnetic field (AMF) contacts are widely used in vacuum interrupters. In this paper, we propose a concept of critical radius of AMF contacts. When coil width and coil height are fixed, the axial magnetic flux density increases first with increasing contact diameter. Then, it reaches a maximum value. Thereafter, the axial magnetic flux density decreases. The contact radius corresponding to the maximum axial magnetic flux density is critical radius. The concept of critical radius is validated by coil-type AMF contacts and slot-type AMF contacts in MV vacuum interrupters with finite-element analysis. Critical radius is only related to contact geometry parameters and the current has no influence on critical radius. Critical radius increases with increasing contact gap, coil width, coil height, and thickness of the contact plate. In high-voltage AMF vacuum interrupters, axial magnetic flux density per kiloampere increases with increasing contact diameter since the critical radius is typically high with a high contact gap and it is in the rising branch. In an MV AMF vacuum interrupter, inter-rupting capacity could increase with an increase of the contact diameter with a different rising rate before and after the critical radius. This is expected to be experimentally validated.
Comparison of Axial Magnetic Field Characteristics of Four Axial Magnetic Field Vacuum Interrupter Contacts

Zhongyi Wang,ZhiYuan Liu,Xuan Zhang,Yuesheng Zheng,Jimei Wang

DOI: https://doi.org/10.1109/DEIV.2006.357303

2006-01-01

Abstract:Magnetic characteristics of axial magnetic field (AMF) of four kinds of vacuum interrupter contacts are studied with 3D finite element method, which included axial magnetic flux density, eddy current in contact plates and phase shift time between AMF and source current. Four AMF vacuum interrupter contacts are studied, which include coil type, cup type, bipolar type and quadrapolar type. The results show that: 1) The strongest AMF at current peak is with coil type contact. It follows by bipolar type, cup type, quadrapolar type with which AMF weakens accordingly. 2) The weakest AMF at current zero is with quadrapolar type contact. It follows by bipolar type, cup type, coil type with which AMF strengthens accordingly. 3) The shortest phase shift time is with bipolar type. It follows by quadrapolar type, coil type, cup type with which phase shift time becomes higher accordingly
Research and Design of Permanent Magnetic Actuator for High Voltage Vacuum Circuit Breaker

SH Ma,JM Wang

DOI: https://doi.org/10.1109/isdeiv.2002.1027415

2002-01-01

Abstract:In order to meet the on off requirement of high voltage vacuum circuit breaker, a novel scheme remodeling the static core of permanent magnetic actuator into the basin shape is presented in this paper, furthermore the control circuit and circuit approach are also given.
Development of 126 kV Single-break Vacuum Circuit Breaker

Haomin Li,Yingsan Geng,Zhiyuan Liu,Jianhua Wang

DOI: https://doi.org/10.1109/HOLM.2018.8611686

2018-01-01

Abstract:The objective of this paper is to present development of 126 kV single-break vacuum circuit breaker. Three kinds of electrodes were compared, which were 3/4 coil type, horseshoe type, and slotted horseshoe type geometry. Characteristics of axial magnetic field, vacuum arcs, temperature-rise and short circuit current interruption were analyzed based on simulation and experiment. Average ring current density in electrode disc of 3/4 coil type, horseshoe type and slotted horseshoe type electrode at current of 40 kA was 1.7×10 7 ,(5.5 ×10 7 , and 3.5× 10 7 ,A/m 2 ,respectively. The maximum value of phase shift time of these three geometries region were 1.18, 1.57, and 0.48 ms, respectively. Two vacuum arcs columns with self-balance process was observed for horseshoe type electrode. 3/4 coil type electrode presented one arc column. Besides, vacuum interrupter with 3/4 coil type electrode met temperature-rise requirement at current of 2500 A according to simulation and experiment. Vacuum interrupter with slotted horseshoe type was suitable for normal current of 3150 A according to simulation. Finally, a 126 kV single-break vacuum circuit breaker with 3/4 coil type electrode was developed. It has passed type test according to standard ICE 62270-100.

Bipolar Axial Magnetic Field Electrode for Vacuum Interrupter

Analysis of Axial Magnetic Field electrode applied to high voltage Vacuum Interrupters

High-interrupting-capability vacuum interrupter with two-pole axial magnetic field electrode

DEVELOPMENT AND STUDY ON IRON CORE STYLE BIPOLAR AXIAL MAGNETIC FIELD VACUUM INTERRUPTER

A New Electrode Applied to High Voltage Vacuum Interrupter and Its Performance

Study on a New Single Coil-Type Axial Magnetic Field Contact for High-Voltage Vacuum Interrupters

Analysis of Axial Magnetic Field of an Iron Style Bipolar Axial Magnetic Field Vacuum Interrupter

Analysis of static magnetic field of an iron style bipolar axial magnetic field vacuum interrupter by 3D finite element method

Numerical Analysis on Magnetic Field Characteristic of Axial Magnetic Field Contacts under Long Break Distance

Critical Axial Magnetic Field for Prevention of Anode Spot Formation in Vacuum Interrupters

3D Modeling and Simulation of High-Current Vacuum Arc Subjected to Real External Transverse Magnetic Field

Investigation of DC Vacuum Arc Interruption Ability with Combined Axial and Radial Magnetic Field

Axial magnetic field strength needed for a 126kV single break vacuum interrupter

Calculation ana Analysis of the Electric Field Distribution in High-voltage Interrupter and Its Advance Structure

Arc Behaviours in Vacuum Interrupters with Axial Magnetic Field Electrodes

Research on Vacuum Arc Characteristics of a New Electrode Structure Applied in High Voltage Vacuum Interrupter

A Low Resistance Vacuum Interrupter Electrode with Hook Support under Contact Plates

Critical Radius of Axial Magnetic-Field Contacts in Vacuum Interrupters

Comparison of Axial Magnetic Field Characteristics of Four Axial Magnetic Field Vacuum Interrupter Contacts

Research and Design of Permanent Magnetic Actuator for High Voltage Vacuum Circuit Breaker

Development of 126 kV Single-break Vacuum Circuit Breaker