Abstract:<p>Polypropylene (PP) has been commonly used as packaging materials due to the favorable mechanical and optical properties related to its diverse and complex chain microstructure which can be better understood through effective fractionation. In this work, two commercial PP resins (A and B) with similar bimodal melting temperature distribution in the range of 100–160 °C but different ethylene content (9.1–12.3 mol%) are fractionated by preparative temperature rising elution fractionation (P-TREF) and relevant fractions are characterized by a variety of techniques such as high temperature-gel permeation chromatography (HT-GPC), differential scanning calorimetry (DSC), <sup>13</sup>C nuclear magnetic resonance (NMR) spectroscopy, Fourier transform-infrared (FT-IR) spectroscopy, and wide-angle X-ray diffraction (WAXD). The chain microstructures of the two resins used as food packaging film exhibit heterogeneity and some differences, which are mainly caused by broad and different distribution of ethylene comonomers. Resin B contains more ethylene units than resin A, and the ethylene units are incorporated into the PP chains in the forms of individual unit or very short segments, resulting in large amount of fractions with relatively low isotacticity and crystallinity that eluted at the temperature range of 35–90 °C. These fractions account for 84.07 wt% of resin B, whereas 59.66 wt% of resin A. The propylene sequences of different isotacticity and crystallinity generated by the insertion of ethylene comonomers in resin B are mainly responsible for its biomodal melting behavior. However, ethylene comonomers tend to insert into the PP chains of resin A in the forms of long polyethylene (PE) blocks and generate propylene−ethylene block copolymers with high crystallizability which can be eluted at high temperatures of 120–140 °C. These fractions constitute 3.16 wt% of resin A, but barely exist in resin B. Moreover, 35.83 wt% of resin A were eluted at 110 °C, whereas only 13.22 wt% of resin B can be eluted at this temperature. These fractions with high isotacticity and molecular weight eluted at high temperatures contribute to the higher flexural modulus of resin A. Both long ethylene blocks and propylene sequences of different lengths contribute to the biomodal melting peaks on the thermogram of resin A.</p>

The Structure Characterization of Ethylene-Propylene Random Copolymers for Hot Water Piping

Chain Structure and Mechanical Properties of Ethylene Copolymers in Two Operating Modes of Fluidized Bed Polymerization Reactor

Compositional Differences of Propylene–ethylene Block Copolymers Manufactured by Degradation and Hydrogenation Techniques

Studies on composition and molecular structure of high impact polypropylene

Thermal and Mechanical Properties of Ultrahigh-Molecular-Weight Ethylene/1-Hexene Copolymers Prepared by Living Polymerization with Fluorinated Bis(Phenoxy-Imine) Titanium(Iv) Catalyst

Comparison of chain microstructure between two propylene−ethylene copolymer resins with bimodal melting temperature distribution

Structure and Properties of the Special Random Copolymer of Propylene for Pipes

Stereochemical Heterogeneity of Biodegradable Poly(L-Lactide) Homopolymer As Revealed by Temperature Rising Elution Fractionation and Successive Self-Nucleation/Annealing Thermal Fractionation

Separation and identification of ethylene-propylene block copolymer

Tensile Behaviour of Homogeneous Ethylene Copolymers

Effect of Molecular Weight Distribution on Rheological, Crystallization and Mechanical Properties of Polyethylene-100 Pipe Resins

Dynamic Rheology Behavior of Bimodal Polyethylene

Relationship Between Structure and Properties of PE100 Resins

Thermal fractionation and effect of comonomer distribution on the crystal structure of ethylene–propylene copolymers

Polypropylene random copolymer in pipe application: Performance improvement with controlled molecular weight distribution

Effect of copolymerized ethylene unit on the crystallization behavior of poly(propylene-co-ethylene)s

Chain microstructure of two in-reactor alloy impact polypropylene resins with same stiffness and different toughness

Design of molecular structure for commercial polyethylene100 pipe

Facile Synthesis Of Ethylene-Propylene Fully Alternating Copolymer And Comparison With Random Copolymer Of Similar Composition

Comparison of chain structures between high-speed extrusion coating polyethylene resins by preparative temperature rising elution fractionation and cross-fractionation

Structure and properties of monomodal PE100 for pipes