Abstract:<p>Polypropylene (PP) has been commonly used as packaging materials due to the favorable mechanical and optical properties related to its diverse and complex chain microstructure which can be better understood through effective fractionation. In this work, two commercial PP resins (A and B) with similar bimodal melting temperature distribution in the range of 100–160 °C but different ethylene content (9.1–12.3 mol%) are fractionated by preparative temperature rising elution fractionation (P-TREF) and relevant fractions are characterized by a variety of techniques such as high temperature-gel permeation chromatography (HT-GPC), differential scanning calorimetry (DSC), <sup>13</sup>C nuclear magnetic resonance (NMR) spectroscopy, Fourier transform-infrared (FT-IR) spectroscopy, and wide-angle X-ray diffraction (WAXD). The chain microstructures of the two resins used as food packaging film exhibit heterogeneity and some differences, which are mainly caused by broad and different distribution of ethylene comonomers. Resin B contains more ethylene units than resin A, and the ethylene units are incorporated into the PP chains in the forms of individual unit or very short segments, resulting in large amount of fractions with relatively low isotacticity and crystallinity that eluted at the temperature range of 35–90 °C. These fractions account for 84.07 wt% of resin B, whereas 59.66 wt% of resin A. The propylene sequences of different isotacticity and crystallinity generated by the insertion of ethylene comonomers in resin B are mainly responsible for its biomodal melting behavior. However, ethylene comonomers tend to insert into the PP chains of resin A in the forms of long polyethylene (PE) blocks and generate propylene−ethylene block copolymers with high crystallizability which can be eluted at high temperatures of 120–140 °C. These fractions constitute 3.16 wt% of resin A, but barely exist in resin B. Moreover, 35.83 wt% of resin A were eluted at 110 °C, whereas only 13.22 wt% of resin B can be eluted at this temperature. These fractions with high isotacticity and molecular weight eluted at high temperatures contribute to the higher flexural modulus of resin A. Both long ethylene blocks and propylene sequences of different lengths contribute to the biomodal melting peaks on the thermogram of resin A.</p>

Comparison of chain structures between high-speed extrusion coating polyethylene resins by preparative temperature rising elution fractionation and cross-fractionation

Chain Structure and Mechanical Properties of Ethylene Copolymers in Two Operating Modes of Fluidized Bed Polymerization Reactor

Microstructure characterization of one high-speed extrusion coating polyethylene resin fractionated by solvent gradient fractionation

Studies on composition and molecular structure of high impact polypropylene

Comparison of chain microstructure between two propylene−ethylene copolymer resins with bimodal melting temperature distribution

The Chain Microstructure And Condensed Structure Of Polyethylene Resin Used For Biaxially Stretched Film

Chain microstructure comparison of two transparent polypropylene resins fractionated by temperature rising elution fractionation

Chain microstructure of two in-reactor alloy impact polypropylene resins with same stiffness and different toughness

Characterization on the Chain Heterogeneity of L-Lactide and Epsilon-Caprolactone Copolymers

Stereochemical Heterogeneity of Biodegradable Poly(L-Lactide) Homopolymer As Revealed by Temperature Rising Elution Fractionation and Successive Self-Nucleation/Annealing Thermal Fractionation

Structure-rheology properties of polyethylenes with varying macromolecular architectures

Effect of copolymerized ethylene unit on the crystallization behavior of poly(propylene-co-ethylene)s

Separation and identification of ethylene-propylene block copolymer

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Characterization of Microstructure of Polypropylene Alloys

Elucidation of the relationships of structure-process-property for different ethylene/α-olefin copolymers during film blowing: An in-situ synchrotron radiation X-ray scattering study

CRYSTAF, DSC and SAXS Study of the Co-Crystallization, Phase Separation and Lamellar Packing of the Blends with Different Polyethylenes

Rheological Properties and Crystallization Behaviors of Long Chain Branched Polyethylene Prepared by Melt Branching Reaction

Design of molecular structure for commercial polyethylene100 pipe

Simultaneous Saxs/Waxs/Dsc Studies On Microstructure Of Conventional And Metallocene-Based Ethylene-Butene Copolymers

Structure–property relationship in film and blow molding type high‐density polyethylene polymers from a slurry‐process industrial plant