Abstract:Amorphous 2Mg–Fe+xwt.% Ni alloys were synthesized by mechanical alloying of Mg and Fe elemental powders. Two kinds of ball-milling atmospheres, namely, (1) under argon and (2) first under argon and then in tetrahydrofuran (THF), were examined in this study. The effects of the Ni addition and ball-milling time and atmosphere on the microstructure and electrochemical properties of the prepared alloys have been investigated systematically. The results show that the ball-milled (2Mg–Fe) nickel-free mixture still maintains Mg and Fe elemental phases, and its discharge capacity is only 19.2mAhg−1. The Ni powder addition is advantageous for the formation of Mg–Fe amorphous structure and for the improvement of the electrochemical properties of the alloys. For the alloys milled under argon, with the Ni content x increasing, the discharge capacity of the alloys increases first and then decreases, and reaches a maximum value of 455.3mAhg−1 as x=100. With the milling-time extending, the discharge capacity of the alloy increases first and then decreases too. For the alloys milled under argon and then in THF, the alloys exhibit higher degree of amorphorization, bigger specific surface area and more active surfaces, and thus have better electrochemical properties than those milled under argon. With the Ni increasing, the discharge capacity increases from 249.7mAhg−1 (x=50) to 565.2mAhg−1 (x=150) and then decreases to 497.9mAhg−1 (x=200), and the exchange current density I0 increases from 104.8mAg−1 (x=50) to 251.1mAg−1 (x=200), which is consistent with the variation of the HRD of the alloy electrodes in the investigation range.

Electrode properties of melt-spun Mg–Ni–Nd amorphous alloys

Microstructural Investigation and Electrochemical Property of Mg63Ni27Nd10 Amorphous Alloy

Electrochemical properties of amorphous Mg–Fe alloys mixed with Ni prepared by ball-milling

Thermal Stability and Electrode Properties of Melt-Spun Mg65cu25nd10 Amorphous Alloy

Microstructure and electrochemical properties of amorphous composites of ball-milled Mg2Ni0.95Sn0.05 + x wt% Ni

Enhanced Electrochemical Performance of Mg2ni Alloy Prepared by Rapid Quenching in Magnetic Field

Microstructure and electrochemical properties of amorphous Mg-Fe-Ni hydrogen storage electrode material

An electrochemical investigation of mechanical alloying of MgNi-based hydrogen storage alloys

Microstructures and electrochemical hydrogen storage properties of novel Mg–Al–Ni amorphous composites

Preparation and Discharge Properties of Amorphous Mg_(65-x)Ni_(21)Pr_(14) Agx Alloy Electrodes

Properties of Amorphous Mg 65 Ni 10 RE 25 (re=la, Ce, Pr, Nd, Mm) Hydrogen Storage Alloys Electrode

Electrode Properties and the Dehydrogenation Process of Amorphous Mg–Ni–La Alloys

The Relation Between the Discharge Capacity and Cycling Number of Mechanically Alloyed MgxNi100−x Amorphous Electrode Alloys

A Discussion on Decay of Discharge Capacity for Amorphous Mg–Ni–Nd Hydrogen Storage Alloy

Preparations and Electrochemical Properties of Amorphous Ti-Al Alloys

Microstructural Investigation of Electrochemical Hydrogen Storage in Amorphous Mg–Ni–La Alloy

The electrochemical properties of LaxMg3-xNi9 (x = 1.0-2.0) hydrogen storage alloys

Amorphization and Electrochemical Hydrogen Storage Properties of Mechanically Alloyed Mg–Ni

Hydrogen-storage properties of amorphous Mg–Ni–Nd alloys

Influence of Ball-milling with Ni Powder on the Phase Structure and Electrochemical Hydrogen Storage Properties of Mg17Al12 Alloy

Electrode Characteristics of Non-Stoichiometric Ml(Nimnalfe)(X) Alloys