Abstract:Blending type of ABS with different polybutadiene rubber (PB) and polyacrylonitrile (AN) contents in SAN phase is prepared at 240 degrees C to study the effects of PB and AN content on the structure and the properties of DB/ABS blends. Different kinds of productive ABS along with the blend-type ABS are used to compare the properties of PC/ABS and DB/ABS blends comprehensively. All blends are made by melt blending for 10 min with sheer rate of 30 r/min. The result shows that, in DB/Blend-type ABS (70/30) blends, PB content exhibits significant influence on the tensile properties. Samples with 6.3 wt% of PB always show the best performance both in yield strength and elongation at break when AN content is fixed at 18 wt%, 25 wt% and 30 wt%; while increasing AN content in the sample with the same PB content would result in better blends properties even not so obvious as PB content. Scanning electron microscopy gives exactly the same trend for phase morphology with PB and AN contents, revealing best uniform scale of dispersed phase (ABS) among 0.5 - 1.2 mu m at 6.3 wt% of PB. Thermal gravimetric analysis shows that all DB/ABS blends have good thermal stability, which is not obviously affected by PB content and AN content. Single peak of glass transition shows good compatibility in the DB/ABS blends. Excellent compatibility of DB with ABS in the sample is exhibited through dynamic mechanical analysis. The glasstransition temperature of DB/ABS blends are closed to that of DB, mildly affected by PB and AN content. Besides, both blending type ABS and different kinds of productive type ABS are used to compare the properties of DB/ABS blends and traditional bisphenol-A-type PC/ABS blends. Basic laws of tensile properties in DB/ABS remain the same as in PC/ABS blends using different types of ABS.

Study of Compatibility, Morphology Structure and Mechanical Properties of Cpvc/Abs Blends

Influence of the Tert‐dodecyl Mercaptan Content in Poly(acrylonitrile‐butadiene‐styrene) on Properties of Chlorinated Polyvinyl Chloride/poly(acrylonitrile‐butadiene‐styrene) Blends

Study on the Compatibility and Properties of PVC/ABS/CPE Blends

Blends of poly(vinyl chloride) with α‐methylstyrene‐acrylonitrile‐butadiene‐styrene copolymer: Thermal properties, mechanical properties, and morphology

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Structure and Properties of Isosorbide type Polycarbonate/ABS Blend

Blends of Poly(vinyl Chloride) with Acrylonitrile‐chlorinated Polyethylene‐styrene Copolymer. II. Mechanical Properties

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

A Study on Properties of Poly(vinyl Chloride)/poly(α-Methylstyrene-acrylonitrile) Binary Blends

A STUDY ON POLYVINYL-CHLORIDE) BLENDS WITH CHLORINATED POLYETHYLENE AND ACRYLIC RESIN

Effect of Compatibilizer on the Mechanical Property and Morphostructure of ABS/PBT Blends

Microstructures and Properties of PVC/CPE and PVC/ABS Blends

Compatibility and Thermal Properties of Poly(acrylonitrile–butadiene–styrene) Copolymer Blends with Poly(methyl Methacrylate) and Poly(styrene‐co‐acrylonitrile)

Compatibilizing and toughening of the styrene and acrylonitrile copolymer and core‐shell impact modifier obtained by agglomerate technologies

Morphology and Mechanical Properties of Polymer Blends of PBT and ABS Compatibilized by Styrene-Maleic Anhydride——The Influence of Blending Procedure

Effect of Abs Grafting Degree and Compatibilization on the Properties of Pbt/Abs Blends

Effect of the Composition of Α‐msan Copolymer on the Miscibility of PVC/α‐MSAN Blends

Effects of Core‐shell Acrylate Particles on Impact Properties of Chlorinated Polyethylene/polyvinyl Chloride Blends

The Effect of Graft Copolymers of Maleic Anhydride and Epoxy Resin on the Mechanical Properties and Morphology of Pp/Abs Blends

Poly (vinyl Chloride)/poly (α‐methylstyrene–acrylonitrile)/acrylic Resin Ternary Blends with Enhanced Toughness and Heat Resistance

Effect of the matrix plasticization behavior on mechanical properties of PVC/ABS blends