Abstract:In this study, the in-situ compatibilization reaction between recycled acrylonitrile-butadiene-styrene copolymer (rABS) and functional styrene-ethylene-butylene-styrene block maleic anhydride (SEBS-g-MAH) was confirmed, which contributed to the toughening phenomenon of rABS, especially the notched impact strength. As mechanical test that manifested, the rABS/SEBS-g-MAH blends are stronger and more ductile than the rABS/SEBS blends. Prominently, the former has great advantage over the latter in terms of improving the impact performance. Scanning electron microscope (SEM) images showed that the compatible segments that were generated by reaction not only improve the interface adhesion of rABS/SEBS-g-MAH blends but also promote the evolution of co-continuous structures, which can be evidently observed after etching. Furthermore, the SEM micrographs of tensile fracture surfaces indicated that the formation of the co-continuous phase and the improvement of interface adhesion are the most profound reasons for the excellent tensile properties of the rABS/SEBS-g-MAH blends. The impact fracture surface revealed that two-phase interface affects crack propagation and shear yielding absorbs more impact energy than simple interface debonding does at higher deformation rates. Meanwhile, rheological analysis demonstrated that the complex viscosity of the rABS/SEBS-g-MAH (80/20 wt%) blend with a co-continuous structure exhibits a maximum positive deviation at low frequencies from the theoretical value calculated using the rule of logarithmic sum, which indicated a connection between co-continuous structure and complex viscosity. In addition, the storage modulus vs. loss modulus curves of the blends revealed that the viscoelastic behavior of rABS/SEBS-g-MAH blends is very similar to that of rABS.

Preparation of Amine-Functionalized Compatilizer for PC/ABS Blends

Research on effect of ABS,MAH,DCP on property of PA6/ABS blend

Creating Super-Tough and Strong PA6/ABS Blends Using Multi-Phase Compatibilizers

The Preparation of Mah/St Multi-Monomer Melt Grafting on Abs and Its Compatibilizer Effect on Pa6/Abs Blends

Effect of Maleic Anhydride Copolymerization Mode on the Properties of PA6/ABS Blends

Properties of Poly(butylene Terephthalate)/bisphenol A Polycarbonate Blends Toughening with Epoxy-Functionalized Acrylonitrile–Butadiene–Styrene Particles

Grafting of maleic anhydride onto waste acrylonitrile butadiene styrene (ABS) and its application for compatibilization of ABS blends

Fatigue resistance and failure behavior of reaction compatibilized PC/ABS blends under tensile cyclic loading

Blends of rABS and SEBS: Influence of In-Situ Compatibilization on the Mechanical Properties

Effect of Compatibilizer and Nucleation Agent on the Properties of Poly(lacticacid)/Polycarbonate (PLA/PC) Blends

Recycled Polycarbonate/acrylonitrile–butadiene–styrene Reinforced and Toughened Through Chemical Compatibilization

Compatibilization Effect of PP-g-(MAH/VAc) on Polypropylene/Polyamide 6 Blends

Blending ABS resin and its effect on structure and properties of PC/ABS BLEND alloy

Tudy of the Compatibility and Properties of PBT/PC Blends

Study of Compatibility, Morphology Structure and Mechanical Properties of Cpvc/Abs Blends

Super Tough PA6/PP/ABS/SEBS Blends Compatibilized by a Combination of Multi-Phase Compatibilizers

Preparation of Polypropylene and Polystyrene with NCO and NH2 Functional Groups and Their Applications in Polypropylene/polystyrene Blends

Compatibilizing modification of polyethersulfone/polycarbonate blend

Effect of Compatibility on the Foaming Behavior of Injection Molded Polypropylene and Polycarbonate Blend Parts

Study of polypropylene/polyethylene terephthalate blends compatibilized with polypropylene double‐grafted maleic anhydride and epoxy resin

Modification of the Grafting Character to Prepare PA6/ABS-g-MA Blends with Higher Toughness and Stiffness