Abstract:The main objective of this research was to investigate the effect of adding CuO (2 wt.%) nanoparticles and changing the cooling rate on the microstructure and mechanical properties of Al (2 wt.%) Si. The addition of CuO nanoparticles to Al-2wt.%Si (alloy A) resulted in a composite alloy (alloy B). Optical microscopy (OM), scanning electron microscopy (SEM) connected to an energy-dispersive spectrometer (EDS), x-ray diffraction (XRD), and positron annihilation Doppler broadening spectroscopy (PADBS) were used to examine the microstructure of alloys. Moreover, Vickers hardness and tensile tests were used to investigate the mechanical properties of the tested alloys. The G1 samples were cooled in the air to ~ 300 K and quenched G2 samples in cold water at 0 °C. The results showed that increasing the strain rate from 0.004 to 0.02 min −1 or decreasing the temperature from 503 to 423 K could increase the hardening parameters, yield stress ( σ y ), ultimate strength ( σ M ), and Young's modulus ( Y ) of all samples. Moreover, H V decreased as the aging temperature climbed from 423 to 503 K. Adding nano-sized CuO or cooling samples resulted in smaller grains. Furthermore, alloy B exhibited the formation of intermetallic compounds (IMCs) CuAl 2 and Cu 3 Si. The XRD data indicated the formation of phases in both alloys at 423, 463, and 503 K. In addition, the dislocation density, lattice strain, and average crystallite size were calculated. It can be seen from the activation energies and stress exponents that dislocation climbs through core diffusion as a control mechanism for both alloys. A significant positive relationship was observed between the value ( H v ) and PADBS parameters for all examined samples. The investigation showed that nano-sized CuO and a rapid cooling rate increased composite specimen hardness. This finding confirms that aluminum and its alloys play a crucial role in various technical applications.

In-situ Observation on Sintering Process of Al-Cu Alloy

STUDY ON SINTERING PROCESS OF ALLOYS OF Al-Zn AND Al-Cu BINARY SYSTEMS

Effect of fluctuating temperature field on the sintering of Al–10Mg alloy

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

STUDY ON SINTERING PROCESS OF Al- 10mg BINARY ALLOY SYSTEM

In Situ Investigation of Al-Ti Mixed Metal System Microwave Sintering by Synchrotron Radiation Computed Tomography

Microstructure Refinement Mechanism of Undercooled Cu55Ni45 Alloys

Microstructural Characterization of the As-Cast and Homogenized Al-Cu-Mg-Ag Alloy

Microstructure Evolution of Aluminum Powder During Sintering

THE EFFECT OF HEATING METHOD TO SINTERING PROCESS OF PURE METAL POWDERS

Effects of sintering time on the microstructure and properties of an Al-Cu-Mg alloy

3D Online Submicron Scale Observation of Mixed Metal Powder's Microstructure Evolution in High Temperature and Microwave Compound Fields

Microstructure evolution, phase decomposition and transition of Al0.8Co0.5Cr1.5CuFeNi HEA during high temperature sintering and mechanical properties corresponding to different microstructures

An Interface Nucleation Rate Limited Sintering Kinetic Model Applied to in Situ Sintering Al2O3-SmAlO3 Composites

Investigation of Microstructures in As-Cast and Homogenized Al-7.8Zn-1.6Mg-1.8Cu Aluminum Alloy

Conjoint analysis of online experiment and phase field simulation for the effect of metal hetero interface on diffusion of microwave sintering

Effect of CuO Nanostructure Addition and Cooling Rate on the Microstructure and Mechanical Characteristics of Hypoeutectic Al-2wt.%Si Alloy

Observation on the ceramic powder evolution during sintering by synchrotron radiation X-ray computed tomography

Fabrication of in situ Al2O3/Al composite via remelting

Research on homogeneous nucleation and microstructure evolution of aluminium alloy melt

In-situ observation microstructure evolution and growth kinetics of lamellar γ phases in Ti44Al alloy during heat treatment