Abstract:Due to native deficiency of the interfacial mismatch between Al2O3 and Al-melt, as well as micron-Al2O3 segregation at matrix grain boundaries (GBs), achieving both high strength and fracture toughness has been the long-lasting challenge for Al-CuO composite fabricated by conventional casting. Herein, we report a novel manufacturing of Al-CuO composite via shift-speed ball-milling (SSBM) of Al-5 wt.% CuO powders and afterwards subjected to hot-pressing (HP) as well as heat treatment. Comprehensive characterization shows that in-situ generation of the two types of Al2O3 with intragranular distribution, including δ*-Al2O3 particles (∼200 nm) and γ-Al2O3 whiskers (length of ∼150 nm, thickness of ∼20 nm), was governed by a diffusion-assisted nucleation-regime ascribing to the intense thermal effect of Al-CuO reaction. The size and spatial distribution of Al2O3 were emphasized to address their contribution to the high mechanical performance of the composite, which exhibits a tensile strength of ∼481 MPa and fracture elongation of ∼16.8 %. Meanwhile, the toughening mechanism of present Al-CuO composite was rationalized on basis of the "dislocation punched zone" and "plastic zone" affected by Al2O3. Both the theoretical analysis and fracture morphology support a reinforcements-matrix interface failure mechanism and the non-uniform distribution of Al2O3 consisting alternant "rich/poor zones" can markedly contribute to the high toughness. The present findings may provide a promising strategy to achieve an intragranular distribution of nano-sized reinforcements in Al-metal oxides composites, which enables increasing strength and ductility of the metal matrix.

Fabrication of in situ Al2O3/Al composite via remelting

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

Fabrication And Microstructure Of In Situ Al2o3 Decomposed From Al-2(So4)(3)-Reinforced Aluminum Matrix Composites

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

Investigation on Microstructure and Properties of Cu–Al2O3 Composites Fabricated by a Novel In-Situ Reactive Synthesis

In situ Al2O3 particle-reinforced Al and Cu matrix composites synthesized by displacement reactions

Nanostructured Composite Obtained by Mechanically Driven Reduction Reaction of Cuo and Al Powder Mixture

Microstructure and Mechanism of In-Situ Al2o3(P)/Al Nano-Composites Synthesized by Sonochemistry Melt Reaction

In Situ Al Based Composites Fabricated in Al-SiO2-C System by Reaction Sintering

Revealing the strengthening and toughening mechanisms of Al-CuO composite fabricated via in-situ solid-state reaction

An In-Situ Technique For Preparing Al-Tib2 And Al-Al3ti Composites

FLEXURAL STRENGTH OF IN-SITU REACTION PROCESSED Al2O3-Al3Ti-Al COMPOSITES

Microstructure and Mechanical Properties of In-Situ Α-Al2o3p/al-12si Composites Fabricated by Direct Melt Reaction Method with Aid of Electromagnetic Stirring

Mechanical Activation-Assisted Solid-State Aluminothermic Reduction of CuO Powders for In-Situ Copper Matrix Composite Fabrication

Preparation and Mechanical Properties of in Situ Submicron MgAl2O4p/6061Al Composites from Al–Mg–SiO2 System

In-situ Al2O3-Al interface contribution towards the strength-ductility synergy of Al-CuO composite fabricated by solid-state reactive sintering

Mechanism of synthesizing Al2O3/Fe-Al composites with nano Al2O3 fibers by in-situ process

In situ fabrication of α-Al2O3 and Ni2Al3 reinforced aluminum matrix composites in an Al–Ni2O3 system

Evaluation of the microstructure of in-situ reaction processed Al3Ti-Al2O3-Al composite

In-situ fabrication of submicron alpha-Al2O3 particle reinforced AlSi9Cu3 alloy matrix composites by TIG arc process