Abstract:Due to native deficiency of the interfacial mismatch between Al2O3 and Al-melt, as well as micron-Al2O3 segregation at matrix grain boundaries (GBs), achieving both high strength and fracture toughness has been the long-lasting challenge for Al-CuO composite fabricated by conventional casting. Herein, we report a novel manufacturing of Al-CuO composite via shift-speed ball-milling (SSBM) of Al-5 wt.% CuO powders and afterwards subjected to hot-pressing (HP) as well as heat treatment. Comprehensive characterization shows that in-situ generation of the two types of Al2O3 with intragranular distribution, including δ*-Al2O3 particles (∼200 nm) and γ-Al2O3 whiskers (length of ∼150 nm, thickness of ∼20 nm), was governed by a diffusion-assisted nucleation-regime ascribing to the intense thermal effect of Al-CuO reaction. The size and spatial distribution of Al2O3 were emphasized to address their contribution to the high mechanical performance of the composite, which exhibits a tensile strength of ∼481 MPa and fracture elongation of ∼16.8 %. Meanwhile, the toughening mechanism of present Al-CuO composite was rationalized on basis of the "dislocation punched zone" and "plastic zone" affected by Al2O3. Both the theoretical analysis and fracture morphology support a reinforcements-matrix interface failure mechanism and the non-uniform distribution of Al2O3 consisting alternant "rich/poor zones" can markedly contribute to the high toughness. The present findings may provide a promising strategy to achieve an intragranular distribution of nano-sized reinforcements in Al-metal oxides composites, which enables increasing strength and ductility of the metal matrix.

Fabrication And Microstructure Of In Situ Al2o3 Decomposed From Al-2(So4)(3)-Reinforced Aluminum Matrix Composites

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

In Situal3ti–al2o3 Intermetallic Matrix Composite: Synthesis, Microstructure, and Compressive Behavior

In situ fabrication and microstructure of Al2O3 particles reinforced aluminum matrix composites

In situ (Al3Zrp+Al2O3np)/2024Al metal matrix composite with controlled reinforcement architecture fabricated by reaction hot pressing

FLEXURAL STRENGTH OF IN-SITU REACTION PROCESSED Al2O3-Al3Ti-Al COMPOSITES

Fabrication of Nanocrystalline Zro2 Particle Reinforced Aluminum Alloy Composite by Squeeze Casting Route

In situ Al2O3 particle-reinforced Al and Cu matrix composites synthesized by displacement reactions

Microstructural characteristic and mechanical properties of the in-situ MgAl2O4 reinforced Al matrix composite based on Al-Mg-ZnO system

Modify the interface between ex-situ γ-Al2O3 and Al matrix via in-situ coating in an Al matrix composite

Preparation and Mechanical and Tribological Properties of A13Zr+6082Al Composites Fabricated by Magnetic Stirring in Situ

Evaluation of the microstructure of in-situ reaction processed Al3Ti-Al2O3-Al composite

Synthesis and characterization of an in-situ Al2O3/Al–Cu composite with a heterogeneous structure

In–situ synthesis of an Al composite reinforced with multi–scale Al12Mo, (Al, Zr, Si) and Al2O3 particles through a multi–stage reaction

Effect of the Stirring Velocity and the SiO 2 Precursor Particles Feeding Rate on the Microstructure of the Al 2 O 3 /SiO 2 /Al Composites Prepared via Stir Casting Process

Microstructure study of hot rolling nanosized in-situ Al2O3 particle reinforced A356 matrix composites

In situ alloying and reinforcing of Al6061 during selective laser melting

Preparation and mechanical and tribological properties of A1(3)Zr+6082Al composites fabricated by magnetic stirring in situ

Revealing the strengthening and toughening mechanisms of Al-CuO composite fabricated via in-situ solid-state reaction

Synthesis and Characterization of In Situ Dendritic/Particulate α-Al(Fe,TM)Si Phase Reinforced Al Matrix Composites

Microstructure of ZrB<sub>2</sub>/6063Al <i>In Situ</i> Composite Processed by Forge