Abstract:With increasing requirements for environmental protection and energy conservation, Al–Cu powder alloys play an important role in machine weight reduction. During the preparation of the Al–Cu powder alloy, an appropriate sintering temperature helps improve the comprehensive performance of the alloys. In this study, powder metallurgy was used to prepare Al–7.5Cu–1Si alloys, and the effects of different sintering temperatures on their relative sintering density, hardness, and tensile strength were studied. The microstructure and phase composition of the alloy were observed and analyzed by scanning electron microscopy and X-ray diffraction, and the mechanical properties of the alloy were studied using a Brinell hardness tester and a universal material testing machine. By analyzing the microstructural changes of the alloys at different sintering temperatures, the optimal sintering temperature of the alloy was determined to obtain the best properties. The results demonstrated that the sintering temperature significantly affected the diffusion and migration of the metal particles inside the alloy. When the temperature was low, numerous pores were present in the alloy, and the degree of bonding between the metal particles was poor. As the temperature increased, the number of pores in the alloy decreased, and good metallurgical bonding occurred between the particles. The relative densities and mechanical properties of the alloys were significantly affected by the sintering temperature. When the temperature was below 570 °C, the relative density and mechanical properties were low. At 590 °C, the alloy underwent deformation and was in an over-sintered state. The best sintering temperature was 570 °C. This is because at this temperature, the relative sintering density, hardness, and tensile strength of the alloy all reached maximum values, which were 98.6%, 71 HB, and 153 MPa, respectively.

STUDY ON SINTERING PROCESS OF ALLOYS OF Al-Zn AND Al-Cu BINARY SYSTEMS

Study of Hot-press Sintering Process of Nanometer Cu-Al_2O_3 Composite

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Effect of fluctuating temperature field on the sintering of Al–10Mg alloy

Research on homogeneous nucleation and microstructure evolution of aluminium alloy melt

Study on diffusion characteristics of Al-Cu systems and mechanical properties of intermetallics

Effects of Zr+Er and Zr+Y on Microstructure and Tensile Properties of Al-Mg-Si-Cu-Mn-Cr Alloys

Effects of sintering time on the microstructure and properties of an Al-Cu-Mg alloy

In situatomic-scale observation of the conversion behavior in a Cu-Zn alloy for twinnability enhancement

Effect of sintering temperature on the microstructure and properties of Al-7.5Cu-1Si alloy

The Effect of In Concentration and Temperature on Dissolution and Precipitation in Sn–Bi Alloys

Tailoring intermetallic phase and mechanical property improvement in a novel Al-Zn-Mg-Cu-Y alloy via homogenization treatment

STUDY ON THE MICROSTRUCTURES AND GRAIN REFINING PERFORMANCE OF Al-Ti-C GRAIN REFINING MASTER ALLOYS

Alloying mechanisms of binary immiscible systems based on tungsten-copper composite materials

Towards high mechanical performance Al–Cu–Mg–Fe–Ni alloy: influence of composition, solution treatment and aged process on microstructural evolution and mechanical properties

Interfacial diffusion and Kirkendall voids evolution in the Copper-Zinc alloy binary interface revealed by in situ transmission electron microscopy

Effect of Cu and Mn content on solidification microstructure, T-phase formation and mechanical property of Al Cu Mn alloys

Effect of Casting Process and Thermal Exposure on Microstructure and Mechanical Properties of Al-Si-Cu-Ni Alloy

A Quantitative Study on the Interaction Between Silicon Content and Heat Treatment on Thermal Conductivity of Al-Si Binary Alloys

Study on the effect of enhanced magnesium and copper contents on microstructure and property of Al-Zn-Mg-Cu alloys with high zinc element content during fabrication processes

Hot Deformation Behavior and Microstructure Evolution of High-Strength Al-Zn-Mg-Cu Alloy