Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Preparation of SiC and Si3N4 Powders by Ammono Sol-Gel Processing

Synthesis, Characterization and Application of Submicron ZrSiO4 Powder Via Sol-Gel-microemulsion-hydrothermal Method

Synthesis of SiC-AlN Ceramic Alloy Powder by the Direct Reactions Between the Constituent Elements.

Preparation of Amorphous Si-B-C-N Powders and Nano-Sized Ceramics

Preparation of SiC-AlN Ceramic Alloy Powder by Direct Reaction Between Constituent Elements and Property Evaluation of Its Sintered Compacts.

Preparation of Zirconia Powders by Sol-gel Process

Fabrication of Fine-Grained Si 3 N 4 -Si 2 N 2 O Composites by Sintering Amorphous Nano-Sized Silicon Nitride Powders

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Aqueous Processing, Hot-Pressing and Mechanical Properties of Silicon Carbide with Al2O3 and Y2O3

Synthesis of SiC-AlN Powder and Characterization of Its HIP-Sintered Compacts.

Preparation of <i>In Situ</i> Synthesized SiC Particles Reinforced Highly Porous Si<sub>3</sub>N<sub>4</sub> Ceramics by Gel-Casting

Combustion Synthesis of MgSiN2 Powders and Si3N4‐MgSiN2 Composite Powders: Effects of Processing Parameters

Gelcasting Process of Silicon Nitride Ceramics

Nano Β-Sialon Powder Synthesized by Carbothermal Reduction and Nitridation of Ultrafine Al2O3-SiO2 Mixture Employing Sol-Gel Techniques

Preparation of High Concentrated Suspension and Gelcasting Process for Silicon Nitride Bonded Silicon Carbide Refractories

Preparation And Properties Of Sintering-Free Low Density Si3n4/Sic Composite Refractory

Effects of Nitrogen Pressure and Diluent Content on the Morphology of Gel-Cast-foam-assisted Combustion Synthesis of Elongated Β-Si3n4 Particles

Synthesis and characterization of nano-sized Si-B-O-N ceramic powders

beta-Si3N4 Powders by Faming SHS and Their Morphology Analysis

Water-Based Gelcasting of Surface-Coated Silicon Nitride Powder

Synthesis of SiC Precursors by a Two-Step Sol–gel Process and Their Conversion to SiC Powders