Abstract:Hexagonal BN particles (BNp) reinforced fused SiO2 matrix composite (BNp/SiO2) was regarded as a very important candidate material for potential applications on wave transparent thermal protection parts. In this study, pressurelessly sintered 15 vol% BNp/SiO2 composites were prepared by cold isostatic pressing (CIP) and gel‐casting routes, respectively, using two kinds of fused silica powders with different particle sizes (5.82 and 3.24 μm in d50, respectively) as starting SiO2. It was demonstrated that the microstructure and mechanical properties of the composites were well dependent on the preforming techniques of green compacts. Gel‐casting preforming route has an overwhelming superiority over CIP route on the thermal stability of fused SiO2 matrix against α‐cristobalite crystallization, sinterability, and thus the mechanical properties. Using the finer fused silica (3.24 μm in d50) as the starting SiO2, the 15 vol% BNp/SiO2 composite sintered at 1375°C get a density of 2.05 g/cm3, the silica matrix primarily keep amorphous phase with uniformly dispersed nanosized α‐cristobalite crystallites (<5 nm in diameter). The bending strength, fracture toughness and Young's modulus all reach the highest values, 101.5 ± 4.3 MPa, 1.57 ± 0.04 MPa·m1/2 and 61.3 ± 2.4 GPa, respectively. Microstructure characteristics, chemical bond information and mechanical properties of the as‐prepared composites are correlated with their preforming routes, starting fused SiO2 particle size, sintering temperature, etc. based on X‐ray diffractometry, scanning electron microscope, transmission electron microscope, high resolution transmission electron microscope, and FT‐IR analysis.

Effects of Nitrogen Pressure and Diluent Content on the Morphology of Gel-Cast-foam-assisted Combustion Synthesis of Elongated Β-Si3n4 Particles

Gel-cast-foam-assisted Combustion Synthesis of Elongated Β-Si3n4 Crystals and Their Effects on Improving the Thermal Conductivity of Silicone Composites

Effects of Pelletization of Reactants and Diluents on the Combustion Synthesis of Si3N4 Powder

The Effect of Diluent on Combustion Synthesis of Si3n4-Sic-Tin Ceramics with Small Diameter

Effect of nitrogen pressure on combustion synthesis of Si3N4-SiC-TiN ceramic

Combustion Synthesis Of Beta-Si3n4 And Beta-Sialon With Elongated Prismatic Micro-Crystals By Adding Srco3 And Nh4f

Combustion Synthesis of MgSiN2 Powders and Si3N4‐MgSiN2 Composite Powders: Effects of Processing Parameters

Combustion synthesis of high flexural strength, low linear shrinkage and machinable porous β-Si3N4 ceramics

Gelcasting Preparation of Porous Silicon Nitride Ceramics by Adjusting the Content of Monomers

Preparation of SiC Coated Graphite Composite Powders by Nitriding Combustion Synthesis

Combustion Synthesis of β-Si<sub>3</sub>N<sub>4</sub> and β-SiAlON with Elongated Prismatic Micro-Crystals by Adding SrCO<sub>3</sub> and NH<sub>4</sub>F

Effect of Preforming Process and Starting Fused Sio2 Particle Size on Microstructure and Mechanical Properties of Pressurelessly Sintered Bnp/Sio2 Ceramic Composites

Effect of the Diluent on Combustion Synthesis of Silicon Nitride

PREPARING Si3N4 CERAMICS WITH HIGH PERFORMANCES BY GELCASTING (I)INFLUENCE OF COATING Si3N4 POWDER ON MECHANICAL PROPERTIES OF THE MATERIAL

Coarse‐grained Β‐si3n4 Powders Prepared by Combustion Synthesis

Gel casting and properties of porous silicon carbide/silicon nitride composite ceramics

Effect of Different Ratios Between Monomer and Cross-linker on Properties of Gel-Cast Porous Silicon Nitride

Preparation of SiC/Si3N4 composites with rod-like microstructure by combustion synthesis

Investigation of Gel Casting Preparation of Micro-Porous Si_3N_4 Ceramics

Effects of Nitrogen Pressure on Microstructure and Mechanical Performance of Porous Silicon Nitride Ceramics

Effect of solid contents on the mechanical properties of SiC-10 wt.%AlN ceramic composites prepared by gelcasting