Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Preparation And Properties Of Sintering-Free Low Density Si3n4/Sic Composite Refractory

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Fabrication and Properties of Al<sub>2</sub>O<sub>3</sub>-SiC/Sialon Composite Refractories

Preparation and Properties of Si<sub>3</sub>N<sub>4</sub>-SiC-C Refractory Materials Composited with Sucrose and Phenolic Resin

Preparation of ZrN-SiAlON-SiC composite refractories with sucrose as bonding agent

Fabrication and Properties of Si<sub>3</sub>N<sub>4</sub>-SiC-C Refractory Composites

Preparation and Properties of SiC Refractories Via Carbonization-Nitridation Reaction

Fabrication and properties of Al 2O 3-SiC/Sialon composite refractories

Preparation of Sialon/Si<sub>3</sub>N<sub>4</sub>-SiC Composite Refractories Using Kyanite Tailings

Synthesis and properties of porous SiN/SiC nanocomposites by carbothermal reaction between SiN and carbon

Preparation of Sialon/Si3N4-SiC Composite Refractories Using Kyanite Tailings

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Effect of Al 2 O 3 addition on properties of non-sintered SiC–Si 3 N 4 composite refractory materials

Densification and Enhancement of Sic Particulate Reinforced Fine Grain Sic Ceramic

Effect of Al2O3 addition on properties of non-sintered SiC–Si3N4 composite refractory materials

Effect of Silicon Addition on Mechanical Properties of Mullite-Sic Composite Refractories

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Si3N4-SiCpComposites Reinforced Byin SituCo-Catalyzed Generated Si3N4Nanofibers

Fabrication and Mechanical Properties of Si3n4/Sic Nanocomposite with Pressureless Sintering and Sinter-Post-Hiping