Abstract:Due to its high bonding energy and low self-diffusion coefficient, silicon nitride (Si3N4) ceramics cannot form a dense structure with prolonged high-temperature insulation or by raising the sintering temperature. To improve the density of the sintered Si3N4 ceramics, additives are added to promote the rearrangement–dissolution–precipitation process of the crystal grains. However, the liquid phase formation temperature of different sintering aid chemical compositions varies, making it challenging to isolate the mechanism and the effect of liquid phase formation temperatures on sintering. Hence, we developed three sintering aids, namely Y2O3-Al2O3 (YA), Y2Si2O7 (Y2S), and Y2Si2O7-Al6Si2O13 (Y2SM), with homologous elements and different liquid phase formation temperatures. These sintering aids can form a liquid phase with SiO2 on the surface of Si3N4 at varying temperatures. We analyzed the sintered Si3N4 ceramic's density, volume shrinkage rate, and microstructure to verify the YA's lower liquid phase formation temperature effect, providing more rearrangement time and increasing sintering density. Conversely, sintering aids with too low liquid phase formation temperatures are more prone to volatilize during high-temperature sintering stages, thereby reducing sintering density. This research found that different liquid phase formation temperatures do not affect the α→β phase transition temperature of Si3N4 ceramics. We also evaluated the Y2S sintering aid contents' effect on Si3N4 ceramics sintering. The results revealed that aiding sintering with too little Y2S content is insufficient for liquid phase production, and hence does not improve sintering density. Conversely, excessive liquid phase can improve density and refine grain size but increases weight loss rate during sintering due to volatilization.

Effects of Sintering Aid on the Sintering Characteristics and Properties of ZnO-SiO2 Ceramics

Influence of CaO content by mass in sintering aid and sintering temperature on the properties of Al2O3-based microwave ceramic materials

Effect of A-site Substitution on Sintering and Dielectric Properties of ZnO-0.5SiO2 Ceramics

Effects Of Catio(3)On Microstructures And Properties Of (1-X) Znal2o4-Xmg(2) Tio4 (X=0.1) Microwave Dielectric Ceramics

Microstructure and microwave dielectric properties of ZnO-B2O3 doped ceramics

Effects of additives on microstructures and microwave dielectric properties of ZnNb2O6 ceramics

Low Temperature Sintering Microwave Dielectric Ceramic of ZnO-Nb2O5-TiO2 with FeVO4 Addition

A New System of Low Temperature Sintering ZnO–SiO2 Dielectric Ceramics

EFFECT OF DOPING IN LOW-TEMPERATURE SINTERING OF Ca[(Li1/3Nb2/3)0.8Ti0.2]O3-σ MICROWAVE DIELECTRIC CERAMICS

Influence of bismuth oxide as a sintering aid on the densification of cold sintering of zirconia

Microwave Dielectric Properties and Low-Temperature Sintering of (zn0.8mg0.2)2sio4–tio2 Ceramics with Li2O–B2O3

Effect of SiO2 Additive on the High-Frequency Properties of Low-Temperature Fired Co2Z

Effect of sintering aids on mechanical properties and microstructure of alumina ceramic via stereolithography

Effects of sintering additives on mechanical properties and microstructure of Si3N4 ceramics by microwave sintering

Enhancing microstructural properties of alumina ceramics via binary sintering aids

A Study on the Effects of Liquid Phase Formation Temperature and the Content of Sintering Aids on the Sintering of Silicon Nitride Ceramics

Low-Temperature Firing and Microwave Dielectric Properties of Zn3nb2o8 Ceramics with Cuo-V2o5-Bi2o3

High sintering and dielectric performance: The improved (Mg, Zn)3B2O6 ceramics with the help of the DFT calculation

Low-Fire Processing of ZrO<sub>2</sub>-SnO<sub>2</sub>-TiO<sub>2</sub>Ceramics

Low temperature sintering and microwave dielectric properties of BaO–0.6ZnO–2.9TiO 2 ceramics using BaCu(B 2 O 5 ) addition