Abstract:Numerous processes have been applied to refine the microstructure and the precipitation of carbides in ultra-high carbon steel (UHCS). However, the evolution of microstructure and carbide precipitation in UHCSs during the hot deformation compression process remains poorly understood. The present study addresses this issue by applying hot deformation compression to Fe-C-Cr-V-Mo UHCS specimens at temperatures of 950–1150 °C under strain rates of 0.01–5 s−1, and evaluating the resulting flow curves and microstructures of the specimens after cooling in air. High deformation temperature and high strain rate conditions are observed to generate flow curve stress peaks, which result in dynamic recrystallization. In addition, dislocation cell formation and substructure are observed at deformation temperatures of 950 °C and 1050 °C, respectively, under a strain rate of 1 s−1. The recrystallized grain structure fraction is found to be positively correlated with the deformation temperature at strain rates less than 5 s−1, and a fully recrystallized grain structure is not obtained at a strain rate of 5 s−1 even at a temperature of 1150 °C. Moreover, the concentration of primary M7C3 carbides is observed to decrease with increasing deformation temperature, and fine precipitated M23C6 particles are observed in the matrix during hot deformation. An increased concentration of precipitated M23C6 particles is also observed in the specimen microstructure at a deformation temperature of 1150 °C and a strain rate of 5 s−1. The recrystallization process is also observed to vary according to M23C6 particle size, where large M23C6 particles are observed to stimulate the formation of recrystallization nuclei and fine M23C6 particles delay or hinder the recrystallization process.

Effect of Compressive Deformation on Carbide Precipitation in a Fe-C-Mo Alloy

Deformation of Fe and Ag Precipitates in Cu Matrix

Stress-strain behavior and microstructural evolution of ultra-high carbon Fe-C-Cr-V-Mo steel subjected to hot deformation

Influence of Cold Deformation on Carbide Precipitation Kinetics in a Fe-22Mn-0.45C TWIP Steel

Compressive deformation behavior of CrMnFeCoNi high-entropy alloy

Effect of Intragranular Κ Carbides and Intergranular Precipitates on the Hot Deformation Mechanism and Dynamic Recrystallization Mechanism of Fe–28Mn–11Al–1.5C–5Cr Lightweight Steel

Effects of molybdenum on hot deformation behavior and microstructural evolution of Fe40Mn40Co10Cr10C0.5 high entropy alloys

Carbide Precipitation Behavior of High‐Alloy Steel During Solidification and Cooling Process

Effect of Cyclic Warm-Rolling Technique on Mechanical Properties of MoCu30 Thin Plates with Heterogeneous Structure

Cyclic warm rolling: A path to superior properties in Mo Cu composites

Effect of Cu addition on the precipitation behavior of M2C carbides in maraging steel

Effect of Molybdenum Addition on the Precipitation of Carbides in the Austenite Matrix of Titanium Micro-Alloyed Steels

Effect of Spheroidizing Annealing on the Carbide Precipitation Behavior of Cr-Mo-V-W Hot Work Die Steels

On effect of particle size distribution on the elastic/plastic deformation of metal matrix composites

Effect of Y addition on microstructure evolution and precipitation of Cu-Co-Si alloy during hot deformation

Deformation substructural evolution in transformation-induced plasticity high-entropy alloy during cold rolling

Microstructure evolution and composition redistribution of FeCoNiCrMn high entropy alloy under extreme plastic deformation

Optimization of thermal stability and mechanical properties of Mo2C carbides via multi-element doping: experimental and theoretical calculations

Deformation mechanism diagram and deformation instability of a Mo–Re alloy during the hot compression

Effects of Cr addition on the constitutive equation and precipitated phases of copper alloy during hot deformation

Effect of annealing temperature on carbide precipitation, microstructure and mechanical properties of Fe-Mn-C- (Cr, Mo, W, Ni, Nb, Ti, V) multi-alloying TWIP steel