Abstract:In this study, three cationic surfactants (hexadecyltrimethylammonium chloride, hexadecyldimethylbenzylammonium chloride, and octadecyltrimethylammonium chloride) were used to modify montmorillonite and polyethylene (PE)/maleic anhydride grafted polyethylene (PE-g-MAH)/organic-montmorillonite (Org-MMT) nano-composites, prepared by two blending processes (direct-melt blending and solution blending). X-ray diffractometry and transmission electron microscopy were used to investigate the intercalation behavior and microstructure of composites. Mechanical properties were also tested. It was found that the intercalation effect of PE/PE-g-MAH/Org-MMT could be enhanced by increasing the content of PE-g-MMT, using the silicate modified by a cationic surfactant with a benzyl group or long alkyl chain, adopting the solution-blending method or using high-density polyethylene as matrix. The degree of crystallinity of composites and the crystalline thickness perpendicular to the crystalline plane [like (110) and (200)] decreased with increasing amounts of PE-g-MAH and, under certain prescription, the crystalline thickness of the composite made by the solution method was much smaller than that made by direct-melt blending. This clearly showed that Org-MMT and PE-g-MAH had a heterogeneous nucleation effect on crystallization of PE from the melt, resulting in a decrease of crystalline thickness, and the heterogeneous nucleation effect was more evident in the nanocomposite made by the solution-blending method than in that made by the direct-melt intercalation process. The tensile strength initially increased and then decreased with increasing contents of PE-g-MAH. The maximum value in tensile strength (23.3 MPa) was achieved when the concentration of PE-g-MAH was 6 wt %. The impact strength increased concomitantly with the content of PE-g-MAH; it was 122.2 J/m when the concentration of PE-g-MAH was 9 wt %. (C) 2004 Wiley Periodicals, Inc.

Study on LLDPE/mPE Thin Film Blown Modified by the Super-fine Ground CaCO_3

Hdpe/Uhmwpe Blown Films Modified by Poe and Caco3

The Influence of Calcium Carbonate on the Mechanical Properties and Phase Morphology of PA6/PP Blend

Polyethylene/maleic Anhydride Grafted Polyethylene/organic‐montmorillonite Nanocomposites. I. Preparation, Microstructure, and Mechanical Properties

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Study on properties of HDPE/LLDPE/POE blown films

Modification of Poly(vinyl Chloride) with Nano-CaCO3 Coated with Poly(methyl Methacrylate)

Dynamic Mechanical Properties and Morphology of High‐density Polyethylene/caco3 Blends with and Without an Impact Modifier

Mechanical Properties and Volume Dilatation of HDPE/CaCO3 Blends with and Without Impact Modifier

Study on Blending of Wall Material of the Nonel Tube by CSW/PE-g-MAH

Study on MAH Grafted LDPE by Melting and Application of Its Product in PC/HDPE Blend

Physical and Thermal Properties of High-Density Polyethylene Film Modified with Polypropylene and Linear Low-Density Polyethylene

High density polyethylene film toughened with polypropylene and linear low density polyethylene

Improved properties of poly(butylene adipate‐co‐terephthalate)/calcium carbonate films through silane modification

Unique crystal morphology and tensile properties of injection-molded bar of LLDPE by adding HDPE with different molecular weights

The Influence of Epoxy Functionalized Acrylate Particles on the Properties of Plasticized Pla Blown Films

Effect of Ethylene/butyl methacrylate/Glycidyl Methacrylate Terpolymer on toughness and biodegradation of poly (l-lactic acid)

Effect of Mixing Poly(lactic Acid) with Glycidyl Methacrylate Grafted Poly(ethylene Octene) on Optical and Mechanical Properties of the Blown Films

Study on the Preparation and Properties of Caco3/Polypropylene Composite Materials

Ductile and biodegradable poly (lactic acid) matrix film with layered structure

Study on Property of HDPE/POE/CaCO3 Blown Films by Masterbatch Way