Abstract:The improvement of mechanical properties of high-density polyethylene (HDPE) and polypropylene (PP) blends was studied by controlling the phase compatibility versus phase separation. In the original injection molding processes,super mechanical properties of blend specimens-have not been got easily. Researches have been carried out in injection molding with high shear injection conditions. It has been pointed out that the compatibility of blends will increase under the strong shear in injection processes due to the raise of LCST curve. After the melt is injected into the cold mold, its temperature and compatibility decrease simultaneously, phase separation takes place and becomes frozen in the specimen. High mechanical properties will be got when the phase separation develope to some extent, but it is difficult to control the phase compatibility and separation. The special method of oscillating packing injection molding under low pressure provides a condition to control the phase separation degree. Because the phase morphology and crystal morphology of HDPE/PP blends compete with each other, it is difficult to control the micro-phase separation. In this paper, the fine structure combined with the micro-phase separation and orientation were controlled by using that special injection method and high strength and high toughness blends were obtained. DSC and WAXD results indicate that the improvement of tensile strength is dependent on the number of shish-kebab crystals and the degree of macromolecule orientation caused by the oscillating packing injection molding. SEM results indicate that the impact strength is dependent on the degree of macro- and micro-phase separation. The high tensile strength 97.1MPa and high toughness 45.5kJ/m(2) of HDPE/PP blends were achieved when the PP content in the blends was 8 % and 20 %, respectively. Which are 4.3 times and 9.5 times as high as the corresponding values of their static specimens respectively. The future work will be carried out to investigate the phase morphology and crystal morphology as well as the possibility of cocrystallization of PP and HDPE under oscillating packing injection conditions.

Physical and Thermal Properties of High-Density Polyethylene Film Modified with Polypropylene and Linear Low-Density Polyethylene

High density polyethylene film toughened with polypropylene and linear low density polyethylene

Modified high-density polyethylene films: preparation, composition and their physical properties

Study on properties of HDPE/LLDPE/POE blown films

Study on Property of HDPE/UHMWPE Blown Film

Preparation of HDPE/UHMWPE/MMWPE Blends by Two-Step Processing Way and Properties of Blown Films

Studies On High Density Polyethylene (Hdpe) Functionalized By Ultraviolet Irradiation And Its Application

Effect of Ethylene‐propylene Copolymer with Residual PE Crystallinity on Mechanical Properties and Morphology of PP/HDPE Blends

Improved Performance Balance of Polyethylene by Simultaneously Forming Oriented Crystals and Blending Ultrahigh-Molecular-Weight Polyethylene

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Mechanical and thermal properties of high-density polyethylene toughened with glass beads

Simultaneously enhancing strength and toughness for impact polypropylene copolymers by regulating the dispersed phase with high density polyethylene

Rheological and Mechanical Properties of Ultrahigh Molecular Weight Polyethylene/high Density Polyethylene/polyethylene Glycol Blends

Low density polyethylene-polypropylene blends: Part 1 - Ductility and tensile properties

Enhanced Strength and Foamability of High-Density Polyethylene Prepared by Pressure-Induced Flow and Low-Temperature Crosslinking

Studies On High Density Polyethylene/Polycarbonate Blend System Compatibilized With Low Density Polyethylene Grafted Diallyl Bisphenol A Ether

Highly oriented single-phase blend films of high- and low-density polyethylene

Unique crystal morphology and tensile properties of injection-molded bar of LLDPE by adding HDPE with different molecular weights

The High Mechanical Properties and Micro-Phase Separation of High Density Polyethylene and Polypropylene Blends

Morphology and mechanical properties of low‐molecular ‐ weight polyethylene and ultrahigh‐molecular‐weight polyethylene films drawn up to 200‐fold

Thermal and Crystallization Properties of HDPE and HDPE/PP Blends Modified with DCP