Abstract:The reactive extrusion of maleic anhydride grafted polypropylene (PP-g-MAH) with ethylenediamine (EDA) as coupling agent was carried out in a co-rotating twin-screw extruder to produce long chain branched polypropylene (LCBPP). Part of PP-g-MAH was replaced by maleic anhydride grafted high-density polyethylene (HDPE-g-MAH) or linear low-density polyethylene (LLDPE-g-MAH) to obtain hybrid long chain branched (LCB) polymers. Compared with the linear PP, PE and their blends, the LCB polyolefins exhibit excellent dynamic shear and transient extensional rheological characteristics such as increased dynamic modulus, higher low-frequency complex viscosity, significantly enhanced melt strength and strain-hardening behaviors. LCB polymers also have higher tensile strength, tensile modulus, impact strength and lower elongation at break than linear polymer and their blends. Supercritical carbon dioxide (scCO2) was introduced in the reactive extrusion process. With the presence of scCO 2, the motor current of twin extruder was decreased and LCB polyolefins with lower MFR, higher complex viscosity and increased tensile strength and modulus were obtained. This indicates that the application of scCO2 can reduce the viscosity of melt in extruder, enhance the diffusion of reactive species, facilitate the reaction between functional groups, and increase the LCB density. The foaming behavior of both linear and LCB polyolefins were studied. The results show that cellular materials produced from the LCB polyolefins have higher weight reduction, smaller cell size and better mechanical properties than those produced from the linear polymers.

High density polyethylene film toughened with polypropylene and linear low density polyethylene

Physical and Thermal Properties of High-Density Polyethylene Film Modified with Polypropylene and Linear Low-Density Polyethylene

Modified high-density polyethylene films: preparation, composition and their physical properties

Biobased Poly(ethylene-co-hexamethylene 2,5-Furandicarboxylate) (PEHF) Copolyesters with Superior Tensile Properties

Study on properties of HDPE/LLDPE/POE blown films

Preparation of HDPE/UHMWPE/MMWPE Blends by Two-Step Processing Way and Properties of Blown Films

Simultaneously enhancing strength and toughness for impact polypropylene copolymers by regulating the dispersed phase with high density polyethylene

Preparation of high melt strength polypropylene by the reactive extrusion process and its foaming application

Effect of Ethylene‐propylene Copolymer with Residual PE Crystallinity on Mechanical Properties and Morphology of PP/HDPE Blends

Fabrication and toughening mechanism of high toughness PP/SEBS/HDPE blends with core‐shell particles

Hdpe/Uhmwpe Blown Films Modified by Poe and Caco3

Studies On High Density Polyethylene (Hdpe) Functionalized By Ultraviolet Irradiation And Its Application

Synergistic Improvement of Toughness of Isotactic Polypropylene: the Introduction of High Density Polyethylene and Annealing Treatment

Ductile and biodegradable poly (lactic acid) matrix film with layered structure

Preparation and characterization of long-chain branched HDPE by UV-induced reactive extrusion at mild temperature

Blend toughening of poly(vinyl chloride) by chlorinated polyethylene/hydroxy ethyl acrylate graft copolymer

Toughening with Little Rigidity Loss and Mechanism for Modified Polypropylene by Polymer Particles with Core–shell Structure

Morphology evolution and mechanical property enhancement of linear low‐density polyethylene by adding disentangled ultrahigh molecular weight polyethylene

Properties of HDPE/UHMWPE Blown Films

Hierarchical structure and properties of high‐density polyethylene (HDPE) microporous films fabricated via thermally‐induced phase separation (TIPS): Effect of presence of ultra‐high molecular weight polyethylene (UHMWPE)

Study on LLDPE/mPE Thin Film Blown Modified by the Super-fine Ground CaCO_3