Abstract:A modified nano-calcium carbonate (R-CCR) was prepared by coating a layer of unsaturated hydroxylfatty acid on the surface of CCR powders using a solid state method; the latter were commercial nano-CaCO 3 modified with stearic acid. FTIR studies indicate that the modifier is combined on the surface of CaCO 3 . PP/EPDM/nano-CaCO 3 ternary composites were prepared by a melt-mixing method. SEM and TEM were utilized to examine the morphology of the composites. The tensile fractured surface of PP/EPDM/R-CCR showed a fibroid morphology and large-scale yield deformation. The impact fractured surface showed that the amount of cavities in the PP/EPDM/R-CCR system was increased, however their size diminished obviously. R-CCR particles were dispersed uniformly in the PP matrix, and their compatibility was distinctly improved as compared to CCR when the amount of R-CCR was 15 h −1 . The tensile strength remained nearly constant (reduced from 27.6 MPa to 27.5 MPa), while the impact strength increased from 9.6 kJ/m 2 to 15.4 kJ/m 2 as CCR was replaced by R-CCR. Meanwhile, the bending strength and bending modulus also increased correspondingly. Furthermore, the impact strength of PP/EPDM/R-CCR was maintained at a high level (15.4 kJ/m 2 ), which was more than the sum of that of PP/EPDM and PP/R-CCR (6.6 kJ/m 2 and 6.1 kJ/m 2 respectively). This indicates that the R-CCR and EPDM have a significant synergistic toughening effect on PP while maintaining the strength and modulus of virgin PP. Both the storage modulus G′ and loss modulus G″ of PP/EPDM and PP/EPDM/R-CCR composites increase with increasing frequency, but the values of G′ and G″ of the tertiary composite are relatively higher than those of the binary system. The loss factor and viscosity decrease with increasing frequency, but there is little difference between tertiary and binary composites. The apparent viscosity η of the tertiary system containing R-CCR is lower than that of the tertiary system containing CCR and virgin PP. The viscosity of the composites sig-nificantly decreases with increasing shear rate. The mea-sured mechanical properties of the composites indicate that replacing CCR with R-CCR for binary composites could simultaneously enhance the toughness and strength of PP.

Study on the Preparation and Properties of Caco3/Polypropylene Composite Materials

Composites of Polypropylene Reinforced with Ultrafine Bamboo-char: Morphology, Mechanical and Thermal Properties

Polypropylene biocomposites reinforced with bamboo particles and ultrafine bamboo-char: The effect of blending ratio

Enhancement on the properties of polypropylene using bamboo particles: Effect of particle sizes and loadings

Mechanical and Thermal Properties of Polypropylene (PP) Composites Filled with CaCO3 and Shell Waste Derived Bio-Fillers

Study on Properties of Modified Bamboo Fiber Reinforced Polypropylene Composites

The Preparation of Polyethylene/Collagen Composites by Using Reactive Compatibilization Process

Study on the Properties and Structure of Polypropylene Modified with Nano-Sized CaCO_3

Effect of Surface Modification of CaCO_3 on Mechanical Properties of PP/CaCO_3 Composite

Effects of PPTA-pulp on the Structure and Properties of PP/CaCO_3 Composites

Effect of Oleic Acid-modified Nano-CaCO3 on the Crystallization Behavior and Mechanical Properties of Polypropylene

The Influence of Calcium Carbonate on the Mechanical Properties and Phase Morphology of PA6/PP Blend

Study of Property of Nano-ZnO/PP and ZnO/CaCO3/PP Composites

PREPARATION PROCESS AND INTERFACE MODIFICATION ON THE MECHANICAL PROPERTIES OF BAMBOO FIBER/ POLYPROPYLENE CARBONATE COMPOSITES

Calcium Carbonate Particles Filled Homopolymer Polypropylene at Different Loading Levels: Mechanical Properties Characterization and Materials Failure Analysis

Preparation and characterization of poly(propylene carbonate)/montmorillonite nanocomposites by solution intercalation

Modification Of Mechanical And Color Properties Of Polypropylene With Colored Nano-Sio2 Prepared From Diatomite

Mechanical Properties of PVC/CPE/CaCO_3 Composites

Surface Modification of Shell Waste and Its Application in Polypropylene Composites

Electrical Resistivity, Crystallization and Mechanical Properties of Polypropylene/Multi-Walled Carbon Nanotube/Calcium Carbonate Composites Prepared by Melt Mixing

Effect of Unsaturated Hydroxyl-Fatty Acid Modified Nano-Caco3 on the Morphological and Rheological Behavior of PP