Abstract:Subzone tensile tests were used to quantitatively study the tensile properties along the equal toughness welded joint of a 30Cr2Ni4MoV steel ultra-supercritical steam turbine rotor. The results show that the weld metal (WM) has lower strength than the base metal (BM) but similar plasticity and work hardening properties; the heterogeneous microstructure of the heat-affected zone (HAZ) results in a gradient distribution of tensile properties. By fitting the stress-plastic strain curve based on the Hollomon equation, there are two hardening exponents n 1 and n 2 in each subzone of the welded joint. Based on the K–M curve of the hardening rate, during uniform plastic deformation before necking, the coarse-grained HAZ (CGHAZ) only experienced two work hardening stages III and IV, and other micorregions of the welded joint exhibited three work hardening stages III ~V. The exponent n 1 represents initial hardening stage III when the plastic strain is less than 0.003, and n 2 represents hardening stages IV~V when the plastic strain is greater than 0.003. The uneven distribution of the exponent n 2 along the joint is related to the differences in the microstructure (tempered martensite or bainite) and carbides. Observing the subzone specimens after tensile testing by TEM, it can be found that dislocation cells appeared in the tempered bainite matrix, which had better work hardening capability than tempered martensite. The lath martensite and granular bainite mixed microstructure and fine granular martensite are beneficial for improving the hardening capabilities and delaying the hardening period, but the carbides distributed in the high-angle grain boundaries are not conducive to strain hardening. The microstructure type, grain size and carbides dispersed in the matrix are the main factors affecting the hardening behavior of each subzone of the joint. The strength prediction model of welded joint subzones based on the hardness and the hardening exponent was established.

Residual Stress of Joints of Welded Turbine Rotors,Part 3: Residual Stress of 125 MW and 1 000 MW LP Turbine Rotors

Simulation of Residual Stress in Welded Steam Turbine Rotor and Its Effects on Fatigue Life

Calculation of Finite Element of Thermal Stress and Analysis of Low-cyclic Fatigue Life for Non-central Hole Rotor of 135 MW Turbine

Release and Redistribution of Residual Stress in the Welded Turbine Rotor under Service-Type Loadings

Numerical Investigation on Stress Distribution and Evolution in 9cr/2.25cr Dissimilar Welded Rotor Undergoing Welding and Heat Treatment

Research of Welding Residual Stress of Francis Turbine Runner

Stress relief investigation using creep model considering back stress in welded rotor

Study on Numerical Model for Welding Process of Steam Turbine Rotor Based on Three-Dimensional Finite Element Method

Effects of shrinkage fitting on the welding residual stresses of a large electromotor rotor

Effect of geometric construction on residual stress distribution in designing a nuclear rotor joined by multipass narrow gap welding

Numerical Studies of Post Weld Heat Treatment on Residual Stresses in Welded Impeller

Optimization of Welding Joint Between Tower and Bottom Flange Based on Residual Stress Considerations in a Wind Turbine

Virtual Optimization of Regulating and Controlling on Welding Residual Stress of Francis Turbine Runner

Stress Analysis on Complex Shrunk-on Rotor of Steam Turbines

Reduction of Welding Residual Stress in the Head-Cylinder Joint of a Large Rectifying Tower by Finite Element Method and Experimental Study

Research on Surface Residual Stress By Milling 20Cr2NiMo Used for Turbine Rotors

Effect of Welding Technologies on Decreasing Welding Residual Stress of Francis Turbine Runner

Computation of Dynamic Stresses in Piston Rods Caused by Unsteady Hydraulic Loads

Study On Structural Optimization Of Large Power Steam Turbine High Pressure Rotor Based On Thermal-Structural Coupling Analysis

Effect of Microstructure on Local Strain Hardening Behavior along an Equal Toughness Matching Welded Joint of a 30cr2ni4mov Welded Rotor

Stress variation of a gas turbine tie-bolt rotor with Hirth serrations considering assembling and thermal effects