Abstract:Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy, Ahead of Print. In the field of design and optimization of sophisticated geometries such as film-cooled turbine blades of modern jet engines, Computational Fluid Dynamics (CFD) simulation is commonly employed. As the pursuit for higher turbine entry temperatures intensifies, it becomes crucial for computational analyses to offer accurate predictions of metal temperatures and heat transfer coefficients on these critical components. This study investigates the impact of key physical factors that characterize the operation of these components on the accuracy of the computational model. In particular, the effects of including the exchange of thermal energy between the fluid and solid domains, as well as modelling the unsteady interaction between the rotor and stator are studied. The research focuses on a fully featured one-and-a-half stage high-pressure turbine of a commercial jet engine, utilizing proprietary software for conducting 3D Reynolds-Averaged Navier-Stokes flow simulations. To model the fluid-solid thermal interaction, steady-state Conjugate Heat Transfer (CHT) simulations are performed. The CHT results are then compared with experimental data obtained from a thermal paint test, achieving good levels of agreement. Additionally, phase-lag simulations are executed under adiabatic-wall conditions to evaluate the influence of stator-rotor interaction on near-wall gas temperatures. This work shows that, by modelling the periodic unsteadiness at the stator-rotor interface with a phase-lag technique, the maximum near-wall gas temperature prediction is significantly increased, sometimes more than 100K, with respect to the steady-state model one. Findings from this work also suggest that simplified "strip" source terms used to model the presence of film cooling hole rows on the surface of a blade can be used with satisfactory accuracy only for nominal conditions. The mass flows delivered by each source strip should not be linearly scaled based on mainstream quantities for use in different conditions, but they should be recalculated from scratch for the new conditions.

Transient Thermal Stress Analysis of Power Turbine Welded Rotor in a Heavy-Duty Gas Turbine During Rapid Load Changes

Optimization of Start-up Process in Combined Cycle Steam Turbine of a Power Plant

Study on Quick Start-up of Steam Turbine in a Gas-Steam Combined Cycle

Optimization on Start-up Process of Steam Turbine in Combined Cycle Generating Units

Damage Analysis and Start-Up Schedule Optimization of Steam Turbine Rotors With an Anisotropic Damage Coupled Viscoplastic Constitutive Model

Towards Predictive Maintenance of a Heavy-Duty Gas Turbine A New Hybrid Intelligent Methodology for Performance Simulation

Rotor Stress and Dynamics Analysis of a High-Speed Permanent Magnet Machine for a Micro Gas Turbine Considering Multiphysics Factors

Research on low temperature brittleness of 30Cr1Mo1V high-temperature rotor and its life optimization in rapid start-up and warm-up process

Stress variation of a gas turbine tie-bolt rotor with Hirth serrations considering assembling and thermal effects

Heavy-duty gas turbine 3D blade modelling and flow field analysis

Patterns of Growth of an Internal Annular Crack Under the Influence of Thermal Stresses During Turbine Startup

Investigation on Dynamic Stresses of Pump-Turbine Runner during Start Up in Turbine Mode

Rotor Loss Analysis of an External Rotor High‐Speed Permanent Magnet Motor Considering Current Harmonics and Thermal Analysis under High‐Temperature Gas

Pulsation Stability Analysis of a Prototype Pump-Turbine during Pump Mode Startup: Field Test Observations and Insights

Modal Verification and Strength Analysis of Bladed Rotors of Turbine in Rated Working Conditions

Dynamic Stress Analysis of a Large Capacity Pelton Turbine Runner

Dynamic Strain Distribution Monitoring and Fatigue Damage Analysis on a 100 kW Wind Turbine Blade Based on Field Aerodynamic Measurements

Analysis of the aerothermal performance of modern commercial high-pressure turbine rotors using different levels of fidelity

Reconstructing Turbine Non-Uniform Flow Including Hot Streaks Using Spatially Under-Sampled Measurements

Transient Dynamics Analysis On Main Shaft Of Wind Turbine

Computation of Dynamic Stresses in Piston Rods Caused by Unsteady Hydraulic Loads