Abstract:The effect of cold rolling and annealing on texture development and mechanical behavior of Zircaloy-4 alloy plates was systematically investigated in the present work. The as-received plates were subjected to cold rolling with thickness reductions of 33% and 66%. Electron back-scatter diffraction and tensile tests were performed to reveal the texture and mechanical properties, respectively. Results showed that a bimodal texture was featured in the as-received plate and the texture was a fiber that spread from <<math>101¯0</math>> to <<math>112¯0</math>>. After cold rolling and annealing, a fiber with a continuous distribution from <<math>101¯0</math>> to <<math>112¯0</math>> and a fiber with a maximum at the <<math>112¯0</math>> position were present in the plates with thickness reductions of 33% and 66%. Besides, the existence of {<math>0001</math>} basal fiber was noticed, indicating more basal poles oriented toward the normal direction. Tensile tests showed that the recrystallized plate with 66% thickness reduction was more ductile and less strong than that with 33% reduction. Meanwhile, tensile properties were sensitive to strain rate, loading direction and thickness reduction. Moreover, the relationship between texture development and yield strength was discussed based on Schmid theory. Calculated results indicated that prismatic <a> slip was the predominant deformation mode and its Schmid factor values under different loading directions contributed to the anisotropy of yield strength. Due to the texture development during cold rolling and annealing, the averaged SF values for prismatic <a> slip changed with the increased thickness reduction, resulting in the variation of yield strength.</a></a>

Experimental and Simulation Textures in an Asymmetrically Rolled Zinc Alloy Sheet

Rolling Texture Simulation of Aluminium Sheets Based on the Mechanism of Intergranule Reaction Stresses

Texture Evolution of Polycrystalline Aluminum During Rolling Deformation Ii. Theoretical Simulation

Effect of Rolling Paths and Pass Reductions on the Microstructure and Texture Evolutions of AZ31 Sheet with an Initial Asymmetrical Texture Distribution

Texture Evolution in an Al-Cu-Mg Alloy During Hot Rolling

Anisotropic Deformation Mechanisms of Rolling-Textured Zircaloy-4 Alloy by a Crystal Plasticity Model

Computer Simulation of Rolling Textures Evolution of Pure Aluminum with Initial Texture

Texture Evolution of Al-Zn-Mg-Cu Aluminum Alloy Plate During Cold Rolling

Strain Path Dependence of Texture and Property Evolutions on Rolled Mg-Li-Al-Zn Alloy Possessed of an Asymmetric Texture

Tailoring texture in a near-α titanium alloy: Insights from strain paths and cooling rate influences

Influence of Asymmetric Rolling on the Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si Alloy

Texture Formation under Control of S Phase Characteristic and Tensile Property of Hot-Rolling 2A12 Aluminum Alloy Improved by Brass Texture

Slip-induced Texture Evolution of Rolled Mg–6Al–3Sn Alloy During Uniaxial Tension along Rolling and Transverse Directions

Texture Evolution, Deformation Mechanism and Mechanical Properties of the Hot Rolled Mg-Gd-Y-Zn-Zr Alloy Containing LPSO Phase

Strain Rate and Anisotropic Effects on Incipient Plastic Deformation of Zn–Cu–Ti Alloy Sheets

Relationship Between Textures and Deformation Modes in Mg–3Al–1Zn Alloy During Uniaxial Tension

Texture development and mechanical behavior of Zircaloy-4 alloy plates fabricated by cold rolling and annealing

Modeling Texture Evolution During Rolling Process of AZ31 Magnesium Alloy with Elasto-Plastic Self Consistent Model

The Evolution of Microstructure and Texture During Thermomechanical Processing of Al-Mg-Si-Cu Alloy

Texture Evolution During Cold Rolling of Dilute Mg Alloys

Ex-situ EBSD Analysis of Yield Asymmetry, Texture and Twinning Development in Mg–5Li–3Al–2Zn Alloy During Tensile and Compressive Deformation